3.2.18. cg-nat¶
Note
requires a Turbo CG-NAT Application License.
CG-NAT configuration.
vrouter running config# vrf <vrf> cg-nat
enabled¶
Enable/disable CG-NAT in this VRF.
vrouter running config# vrf <vrf> cg-nat
vrouter running cg-nat# enabled true|false
- Default value
true
alg¶
Application-Level Gateway.
vrouter running config# vrf <vrf> cg-nat
vrouter running cg-nat# alg ALG
|
Description |
|---|---|
ftp |
ALG for File Transfer Protocol. |
h323-q931 |
ALG for H.225.0 Call Signaling Protocol. |
h323-ras |
ALG for H.225.0 Registration, Admission and Status Protocol. |
pptp |
ALG for Point-to-Point Tunneling Protocol. |
rtsp |
ALG for Real Time Streaming Protocol. |
sip-tcp |
ALG for Session Initiation Protocol over TCP. |
sip-udp |
ALG for Session Initiation Protocol over UDP. |
tftp |
ALG for Trivial File Transfer Protocol. |
dns-udp |
ALG for Domain Name System. |
pool¶
Pools of IP addresses for the CG-NAT rules.
vrouter running config# vrf <vrf> cg-nat pool <string>
<string> |
Pool name. |
address¶
IPv4 addresses in the pool.
vrouter running config# vrf <vrf> cg-nat pool <string>
vrouter running pool <string># address ADDRESS
|
Description |
|---|---|
<ipv4-address> |
An IPv4 address. |
<ipv4-prefix> |
An IPv4 prefix: address and CIDR mask. |
<ipv4-range> |
An IPv4 address range, in the form addr4-addr4. |
block-allocation-mode¶
Algorithm used to associate blocks to user.
vrouter running config# vrf <vrf> cg-nat pool <string>
vrouter running pool <string># block-allocation-mode BLOCK-ALLOCATION-MODE
|
Description |
|---|---|
dynamic |
Blocks are allocated dynamically to any user. |
deterministic |
Blocks are allocated deterministically. It means the same block is always allocated to the same user. |
- Default value
dynamic
block-size¶
Number of ports that will be assigned to a given user.
vrouter running config# vrf <vrf> cg-nat pool <string>
vrouter running pool <string># block-size <uint32>
rule¶
List of CG-NAT rules.
vrouter running config# vrf <vrf> cg-nat rule <uint16>
<uint16> |
Id and priority of the rule. Higher number means lower priority. |
deterministic-snat44¶
Deterministic source NAT44 translation.
vrouter running config# vrf <vrf> cg-nat rule <uint16> deterministic-snat44
match¶
Match parameters.
vrouter running config# vrf <vrf> cg-nat rule <uint16> deterministic-snat44 match
outbound-interface (mandatory)¶
Interface to match on outbound.
vrouter running config# vrf <vrf> cg-nat rule <uint16> deterministic-snat44 match
vrouter running match# outbound-interface OUTBOUND-INTERFACE
OUTBOUND-INTERFACE |
An interface name. |
source¶
Match on source address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> deterministic-snat44 match source
ipv4-address¶
Match on source address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> deterministic-snat44 match source
vrouter running source# ipv4-address IPV4-ADDRESS
IPV4-ADDRESS |
An IPv4 prefix: address and CIDR mask. |
translate-to¶
Translate to.
vrouter running config# vrf <vrf> cg-nat rule <uint16> deterministic-snat44 translate-to
pool-name (mandatory)¶
Name of IP address pool used for translation.
vrouter running config# vrf <vrf> cg-nat rule <uint16> deterministic-snat44 translate-to
vrouter running translate-to# pool-name <leafref>
max-conntracks-per-user¶
Maximum number of conntracks assigned to a user. When set to 0, the number of conntracks is not limited.
vrouter running config# vrf <vrf> cg-nat rule <uint16> deterministic-snat44 translate-to
vrouter running translate-to# max-conntracks-per-user <uint32>
port-algo¶
Port allocation algorithm for new mappings.
vrouter running config# vrf <vrf> cg-nat rule <uint16> deterministic-snat44 translate-to
vrouter running translate-to# port-algo PORT-ALGO
|
Description |
|---|---|
parity |
Preserve port parity: an even port will be mapped to an even port, and an odd port will be mapped to an odd port. |
random |
Choose port randomly. |
endpoint-mapping¶
NAT endpoint mapping behavior.
vrouter running config# vrf <vrf> cg-nat rule <uint16> deterministic-snat44 translate-to
vrouter running translate-to# endpoint-mapping ENDPOINT-MAPPING
|
Description |
|---|---|
dependent |
Reuse port mapping for subsequent packets sent from the same internal IP address and port to the same external IP address and port. |
independent |
Reuse the port mapping for subsequent packets sent from the same internal IP address and port to any external IP address and port. |
endpoint-filtering¶
NAT endpoint filtering behavior.
vrouter running config# vrf <vrf> cg-nat rule <uint16> deterministic-snat44 translate-to
vrouter running translate-to# endpoint-filtering ENDPOINT-FILTERING
|
Description |
|---|---|
dependent |
Inbound packets from external endpoints are filtered out if they don’t fully match an existing mapping (IP/port src/dst). |
independent |
Inbound packets from external endpoints are filtered out only if their destination IP address and port don’t match an existing mapping (IP/port src can differ). |
hairpinning¶
Enable communication between two hosts on the internal network, using their mapped endpoint.
vrouter running config# vrf <vrf> cg-nat rule <uint16> deterministic-snat44 translate-to
vrouter running translate-to# hairpinning true|false
address-pooling¶
CG-NAT Address Pooling mode.
vrouter running config# vrf <vrf> cg-nat rule <uint16> deterministic-snat44 translate-to
vrouter running translate-to# address-pooling ADDRESS-POOLING
|
Description |
|---|---|
paired |
In paired mode, the same IP of the pool is used to translate all the sessions originating from the same CPE. |
no-paired |
In no-paired mode, different IPs of the pool can be used to translate different sessions originating from the same CPE. |
dynamic-snat44¶
Dynamic source NAT44 translation.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat44
match¶
Match parameters.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat44 match
outbound-interface (mandatory)¶
Interface to match on outbound.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat44 match
vrouter running match# outbound-interface OUTBOUND-INTERFACE
OUTBOUND-INTERFACE |
An interface name. |
source¶
Match on source address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat44 match source
ipv4-address¶
Match on source address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat44 match source
vrouter running source# ipv4-address IPV4-ADDRESS
IPV4-ADDRESS |
An IPv4 prefix: address and CIDR mask. |
translate-to¶
Translate to.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat44 translate-to
pool-name (mandatory)¶
Name of IP address pool used for translation.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat44 translate-to
vrouter running translate-to# pool-name <leafref>
max-blocks-per-user¶
Maximum number of port blocks assigned to a user.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat44 translate-to
vrouter running translate-to# max-blocks-per-user <uint16>
active-block-timeout¶
Interval during which the the current block is used to allocate sessions. When set to 0, the current block is always used.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat44 translate-to
vrouter running translate-to# active-block-timeout <uint16>
user-timeout¶
Interval during which the current block remains active after all user flows have expired.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat44 translate-to
vrouter running translate-to# user-timeout <uint16>
max-conntracks-per-user¶
Maximum number of conntracks assigned to a user. When set to 0, the number of conntracks is not limited.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat44 translate-to
vrouter running translate-to# max-conntracks-per-user <uint32>
port-algo¶
Port allocation algorithm for new mappings.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat44 translate-to
vrouter running translate-to# port-algo PORT-ALGO
|
Description |
|---|---|
parity |
Preserve port parity: an even port will be mapped to an even port, and an odd port will be mapped to an odd port. |
random |
Choose port randomly. |
endpoint-mapping¶
NAT endpoint mapping behavior.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat44 translate-to
vrouter running translate-to# endpoint-mapping ENDPOINT-MAPPING
|
Description |
|---|---|
dependent |
Reuse port mapping for subsequent packets sent from the same internal IP address and port to the same external IP address and port. |
independent |
Reuse the port mapping for subsequent packets sent from the same internal IP address and port to any external IP address and port. |
endpoint-filtering¶
NAT endpoint filtering behavior.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat44 translate-to
vrouter running translate-to# endpoint-filtering ENDPOINT-FILTERING
|
Description |
|---|---|
dependent |
Inbound packets from external endpoints are filtered out if they don’t fully match an existing mapping (IP/port src/dst). |
independent |
Inbound packets from external endpoints are filtered out only if their destination IP address and port don’t match an existing mapping (IP/port src can differ). |
hairpinning¶
Enable communication between two hosts on the internal network, using their mapped endpoint.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat44 translate-to
vrouter running translate-to# hairpinning true|false
address-pooling¶
CG-NAT Address Pooling mode.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat44 translate-to
vrouter running translate-to# address-pooling ADDRESS-POOLING
|
Description |
|---|---|
paired |
In paired mode, the same IP of the pool is used to translate all the sessions originating from the same CPE. |
no-paired |
In no-paired mode, different IPs of the pool can be used to translate different sessions originating from the same CPE. |
dynamic-snat64¶
Dynamic source NAT64 translation.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64
match¶
Match parameters.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64 match
outbound-interface (mandatory)¶
Interface to match on outbound.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64 match
vrouter running match# outbound-interface OUTBOUND-INTERFACE
OUTBOUND-INTERFACE |
An interface name. |
source¶
Match on source address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64 match source
ipv6-address¶
Match on source address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64 match source
vrouter running source# ipv6-address IPV6-ADDRESS
IPV6-ADDRESS |
An IPv6 prefix: address and CIDR mask. |
translate-to¶
Translate to.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64 translate-to
pool-name (mandatory)¶
Name of IP address pool used for translation.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64 translate-to
vrouter running translate-to# pool-name <leafref>
max-blocks-per-user¶
Maximum number of port blocks assigned to a user.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64 translate-to
vrouter running translate-to# max-blocks-per-user <uint16>
active-block-timeout¶
Interval during which the the current block is used to allocate sessions. When set to 0, the current block is always used.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64 translate-to
vrouter running translate-to# active-block-timeout <uint16>
user-timeout¶
Interval during which the current block remains active after all user flows have expired.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64 translate-to
vrouter running translate-to# user-timeout <uint16>
max-conntracks-per-user¶
Maximum number of conntracks assigned to a user. When set to 0, the number of conntracks is not limited.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64 translate-to
vrouter running translate-to# max-conntracks-per-user <uint32>
port-algo¶
Port allocation algorithm for new mappings.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64 translate-to
vrouter running translate-to# port-algo PORT-ALGO
|
Description |
|---|---|
parity |
Preserve port parity: an even port will be mapped to an even port, and an odd port will be mapped to an odd port. |
random |
Choose port randomly. |
endpoint-mapping¶
NAT endpoint mapping behavior.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64 translate-to
vrouter running translate-to# endpoint-mapping ENDPOINT-MAPPING
|
Description |
|---|---|
dependent |
Reuse port mapping for subsequent packets sent from the same internal IP address and port to the same external IP address and port. |
independent |
Reuse the port mapping for subsequent packets sent from the same internal IP address and port to any external IP address and port. |
endpoint-filtering¶
NAT endpoint filtering behavior.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64 translate-to
vrouter running translate-to# endpoint-filtering ENDPOINT-FILTERING
|
Description |
|---|---|
dependent |
Inbound packets from external endpoints are filtered out if they don’t fully match an existing mapping (IP/port src/dst). |
independent |
Inbound packets from external endpoints are filtered out only if their destination IP address and port don’t match an existing mapping (IP/port src can differ). |
hairpinning¶
Enable communication between two hosts on the internal network, using their mapped endpoint.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64 translate-to
vrouter running translate-to# hairpinning true|false
address-pooling¶
CG-NAT Address Pooling mode.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64 translate-to
vrouter running translate-to# address-pooling ADDRESS-POOLING
|
Description |
|---|---|
paired |
In paired mode, the same IP of the pool is used to translate all the sessions originating from the same CPE. |
no-paired |
In no-paired mode, different IPs of the pool can be used to translate different sessions originating from the same CPE. |
destination-prefix¶
NAT64 destination prefix.
vrouter running config# vrf <vrf> cg-nat rule <uint16> dynamic-snat64 translate-to
vrouter running translate-to# destination-prefix DESTINATION-PREFIX
DESTINATION-PREFIX |
An IPv6 prefix: address and CIDR mask. |
static-dnat44¶
Static destination NAT44 translation.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-dnat44
match¶
Match parameters.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-dnat44 match
inbound-interface (mandatory)¶
Interface to match on inbound.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-dnat44 match
vrouter running match# inbound-interface INBOUND-INTERFACE
INBOUND-INTERFACE |
An interface name. |
destination¶
Match on destination address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-dnat44 match destination
ipv4-address¶
Match on destination address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-dnat44 match destination
vrouter running destination# ipv4-address IPV4-ADDRESS
IPV4-ADDRESS |
An IPv4 prefix: address and CIDR mask. |
translate-to¶
Translate to.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-dnat44 translate-to
ipv4-address (mandatory)¶
Translated Address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-dnat44 translate-to
vrouter running translate-to# ipv4-address IPV4-ADDRESS
IPV4-ADDRESS |
An IPv4 address. |
static-dnat46¶
Static destination NAT46 translation.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-dnat46
match¶
Match parameters.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-dnat46 match
inbound-interface (mandatory)¶
Interface to match on inbound.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-dnat46 match
vrouter running match# inbound-interface INBOUND-INTERFACE
INBOUND-INTERFACE |
An interface name. |
destination¶
Match on destination address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-dnat46 match destination
ipv4-address¶
Match on destination address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-dnat46 match destination
vrouter running destination# ipv4-address IPV4-ADDRESS
IPV4-ADDRESS |
An IPv4 prefix: address and CIDR mask. |
translate-to¶
Translate to.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-dnat46 translate-to
ipv6-address (mandatory)¶
Translated Address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-dnat46 translate-to
vrouter running translate-to# ipv6-address IPV6-ADDRESS
IPV6-ADDRESS |
An IPv6 address. |
source-prefix¶
NAT46 source prefix.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-dnat46 translate-to
vrouter running translate-to# source-prefix SOURCE-PREFIX
SOURCE-PREFIX |
An IPv6 prefix: address and CIDR mask. |
static-snat44¶
Static source NAT44 translation.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-snat44
match¶
Match parameters.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-snat44 match
outbound-interface (mandatory)¶
Interface to match on outbound.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-snat44 match
vrouter running match# outbound-interface OUTBOUND-INTERFACE
OUTBOUND-INTERFACE |
An interface name. |
source¶
Match on source address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-snat44 match source
ipv4-address¶
Match on source address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-snat44 match source
vrouter running source# ipv4-address IPV4-ADDRESS
IPV4-ADDRESS |
An IPv4 prefix: address and CIDR mask. |
translate-to¶
Translate to.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-snat44 translate-to
ipv4-address (mandatory)¶
Translated Address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-snat44 translate-to
vrouter running translate-to# ipv4-address IPV4-ADDRESS
IPV4-ADDRESS |
An IPv4 address. |
static-snat64¶
Static source NAT64 translation.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-snat64
match¶
Match parameters.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-snat64 match
outbound-interface (mandatory)¶
Interface to match on outbound.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-snat64 match
vrouter running match# outbound-interface OUTBOUND-INTERFACE
OUTBOUND-INTERFACE |
An interface name. |
source¶
Match on source address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-snat64 match source
ipv6-address¶
Match on source address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-snat64 match source
vrouter running source# ipv6-address IPV6-ADDRESS
IPV6-ADDRESS |
An IPv6 prefix: address and CIDR mask. |
translate-to¶
Translate to.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-snat64 translate-to
ipv4-address (mandatory)¶
Translated Address.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-snat64 translate-to
vrouter running translate-to# ipv4-address IPV4-ADDRESS
IPV4-ADDRESS |
An IPv4 address. |
destination-prefix¶
NAT64 destination prefix.
vrouter running config# vrf <vrf> cg-nat rule <uint16> static-snat64 translate-to
vrouter running translate-to# destination-prefix DESTINATION-PREFIX
DESTINATION-PREFIX |
An IPv6 prefix: address and CIDR mask. |
match¶
Match parameters.
vrouter running config# vrf <vrf> cg-nat rule <uint16> match
outbound-interface (mandatory)¶
Interface to match on outbound.
vrouter running config# vrf <vrf> cg-nat rule <uint16> match
vrouter running match# outbound-interface OUTBOUND-INTERFACE
OUTBOUND-INTERFACE |
An interface name. |
translate-to¶
Translate to.
vrouter running config# vrf <vrf> cg-nat rule <uint16> translate-to
pool-name (mandatory)¶
Name of IP address pool used for translation.
vrouter running config# vrf <vrf> cg-nat rule <uint16> translate-to
vrouter running translate-to# pool-name <leafref>
max-blocks-per-user¶
Maximum number of port blocks assigned to a user.
vrouter running config# vrf <vrf> cg-nat rule <uint16> translate-to
vrouter running translate-to# max-blocks-per-user <uint16>
active-block-timeout¶
Interval during which the the current block is used to allocate sessions. When set to 0, the current block is always used.
vrouter running config# vrf <vrf> cg-nat rule <uint16> translate-to
vrouter running translate-to# active-block-timeout <uint16>
user-timeout¶
Interval during which the current block remains active after all user flows have expired.
vrouter running config# vrf <vrf> cg-nat rule <uint16> translate-to
vrouter running translate-to# user-timeout <uint16>
max-conntracks-per-user¶
Maximum number of conntracks assigned to a user. When set to 0, the number of conntracks is not limited.
vrouter running config# vrf <vrf> cg-nat rule <uint16> translate-to
vrouter running translate-to# max-conntracks-per-user <uint32>
port-algo¶
Port allocation algorithm for new mappings.
vrouter running config# vrf <vrf> cg-nat rule <uint16> translate-to
vrouter running translate-to# port-algo PORT-ALGO
|
Description |
|---|---|
parity |
Preserve port parity: an even port will be mapped to an even port, and an odd port will be mapped to an odd port. |
random |
Choose port randomly. |
endpoint-mapping¶
NAT endpoint mapping behavior.
vrouter running config# vrf <vrf> cg-nat rule <uint16> translate-to
vrouter running translate-to# endpoint-mapping ENDPOINT-MAPPING
|
Description |
|---|---|
dependent |
Reuse port mapping for subsequent packets sent from the same internal IP address and port to the same external IP address and port. |
independent |
Reuse the port mapping for subsequent packets sent from the same internal IP address and port to any external IP address and port. |
endpoint-filtering¶
NAT endpoint filtering behavior.
vrouter running config# vrf <vrf> cg-nat rule <uint16> translate-to
vrouter running translate-to# endpoint-filtering ENDPOINT-FILTERING
|
Description |
|---|---|
dependent |
Inbound packets from external endpoints are filtered out if they don’t fully match an existing mapping (IP/port src/dst). |
independent |
Inbound packets from external endpoints are filtered out only if their destination IP address and port don’t match an existing mapping (IP/port src can differ). |
hairpinning¶
Enable communication between two hosts on the internal network, using their mapped endpoint.
vrouter running config# vrf <vrf> cg-nat rule <uint16> translate-to
vrouter running translate-to# hairpinning true|false
address-pooling¶
CG-NAT Address Pooling mode.
vrouter running config# vrf <vrf> cg-nat rule <uint16> translate-to
vrouter running translate-to# address-pooling ADDRESS-POOLING
|
Description |
|---|---|
paired |
In paired mode, the same IP of the pool is used to translate all the sessions originating from the same CPE. |
no-paired |
In no-paired mode, different IPs of the pool can be used to translate different sessions originating from the same CPE. |
conntrack¶
Conntrack options.
vrouter running config# vrf <vrf> cg-nat conntrack
behavior¶
Specific TCP options.
vrouter running config# vrf <vrf> cg-nat conntrack
vrouter running conntrack# behavior <behavior> enabled true|false
|
Description |
|---|---|
tcp-window-check |
TCP window check. |
tcp-rst-strict-order |
TCP rst strict order. |
timeouts¶
Timeouts for the different events/protocols.
vrouter running config# vrf <vrf> cg-nat conntrack timeouts
icmp¶
Conntrack options for ICMP.
vrouter running config# vrf <vrf> cg-nat conntrack timeouts
vrouter running timeouts# icmp <icmp> <uint32>
|
Description |
|---|---|
new |
State NEW. |
established |
State ESTABLISHED. |
closed |
State CLOSED. |
udp¶
Conntrack options for UDP.
vrouter running config# vrf <vrf> cg-nat conntrack timeouts
vrouter running timeouts# udp <udp> <uint32>
|
Description |
|---|---|
new |
State NEW. |
established |
State ESTABLISHED. |
closed |
State CLOSED. |
gre-pptp¶
Conntrack options for GRE-PPTP.
vrouter running config# vrf <vrf> cg-nat conntrack timeouts
vrouter running timeouts# gre-pptp <gre-pptp> <uint32>
|
Description |
|---|---|
new |
State NEW. |
established |
State ESTABLISHED. |
closed |
State CLOSED. |
tcp¶
Conntrack options for TCP.
vrouter running config# vrf <vrf> cg-nat conntrack timeouts
vrouter running timeouts# tcp <tcp> <uint32>
|
Description |
|---|---|
syn-sent |
State SYN-SENT. |
simsyn-sent |
State SIMSYN-SENT. |
syn-received |
State SYN-RECEIVED. |
established |
State ESTABLISHED. |
fin-sent |
State FIN-SENT. |
fin-received |
State FIN-RECEIVED. |
closed |
State CLOSED. |
close-wait |
State CLOSE-WAIT. |
fin-wait |
State FIN-WAIT. |
last-ack |
State LAST-ACK. |
time-wait |
State TIME-WAIT. |
nat64¶
NAT64 conntrack options.
vrouter running config# vrf <vrf> cg-nat conntrack nat64
option¶
Specific NAT64 options.
vrouter running config# vrf <vrf> cg-nat conntrack nat64
vrouter running nat64# option <option> true|false
|
Description |
|---|---|
update-tcp-mss |
Enable/Disable TCP MSS update. |
drop-udp-zero-checksum |
Enable/Disable UDP null checksum packet drops. |
force-frag-ipv4 |
Fragment IPv4 packets (with DF flag) if the MTU is too small. |
force-frag-ipv6 |
Fragment IPv6 packets if the MTU is too small. |