ripng¶

Note

requires a Product License.

RIPng router configuration.

vsr running config# vrf <vrf> routing ripng

aggregate¶

Set aggregate RIPng route announcement.

vsr running config# vrf <vrf> routing ripng
vsr running ripng# aggregate AGGREGATE

AGGREGATE

An IPv6 prefix: address and CIDR mask.

static-route¶

RIPng static routes.

vsr running config# vrf <vrf> routing ripng
vsr running ripng# static-route STATIC-ROUTE

STATIC-ROUTE

An IPv6 prefix: address and CIDR mask.

enabled¶

Enable or disable router.

vsr running config# vrf <vrf> routing ripng
vsr running ripng# enabled true|false

Default value: true

allow-ecmp¶

Allow equal-cost multi-path.

vsr running config# vrf <vrf> routing ripng
vsr running ripng# allow-ecmp true|false

Default value: false

default-information-originate¶

Control distribution of default route.

vsr running config# vrf <vrf> routing ripng
vsr running ripng# default-information-originate true|false

Default value: false

default-metric¶

Default metric of redistributed routes.

vsr running config# vrf <vrf> routing ripng
vsr running ripng# default-metric <1-16>

Default value: 1

network¶

Enable RIP on the specified IP network.

vsr running config# vrf <vrf> routing ripng
vsr running ripng# network NETWORK

`NETWORK` values	Description
`<ipv4-prefix>`	An IPv4 prefix: address and CIDR mask.
`<ipv6-prefix>`	An IPv6 prefix: address and CIDR mask.

interface¶

Enable RIP on the specified interface.

vsr running config# vrf <vrf> routing ripng
vsr running ripng# interface INTERFACE

INTERFACE

An interface name.

passive-interface¶

A list of interfaces where the sending of RIP packets is disabled.

vsr running config# vrf <vrf> routing ripng
vsr running ripng# passive-interface PASSIVE-INTERFACE

PASSIVE-INTERFACE

An interface name.

redistribute¶

Redistributes routes learned from other routing protocols.

vsr running config# vrf <vrf> routing ripng
vsr running ripng# redistribute <redistribute> metric <0-16> route-map ROUTE-MAP

`<redistribute>` values	Description
`connected`	Connected routes (directly attached subnet or host).
`kernel`	Kernel routes (not installed via the zebra RIB).
`isis`	Intermediate system to intermediate system (ISIS).
`ospf6`	Open Shortest Path First (OSPFv3).
`bgp`	Border Gateway Protocol (BGP).
`static`	Statically configured routes.

metric¶

Metric used for the redistributed route. If a metric is not specified, the metric configured with the default-metric attribute in RIPng router configuration is used. If the default-metric attribute has not been configured, the default metric for redistributed routes is 0.

metric <0-16>

route-map¶

Applies the conditions of the specified route-map to routes that are redistributed into the RIPng routing instance.

route-map ROUTE-MAP

ROUTE-MAP

Route map name.

timers¶

Settings of basic timers.

vsr running config# vrf <vrf> routing ripng timers

flush-interval¶

unit: seconds

Interval before a route is flushed from the routing table.

vsr running config# vrf <vrf> routing ripng timers
vsr running timers# flush-interval <uint16>

Default value: 120

holddown-interval¶

unit: seconds

Interval before better routes are released.

vsr running config# vrf <vrf> routing ripng timers
vsr running timers# holddown-interval <uint16>

Default value: 180

update-interval¶

unit: seconds

Interval at which RIP updates are sent.

vsr running config# vrf <vrf> routing ripng timers
vsr running timers# update-interval <uint16>

Default value: 30

distribute-list¶

Filter networks in routing updates.

vsr running config# vrf <vrf> routing ripng
vsr running ripng# distribute-list <interface> <update-direction> access-list ACCESS-LIST \
... prefix-list PREFIX-LIST

`<interface>` values	Description
`<ifname>{1,15}`	An interface name.
`all`	Match all interfaces.

`<update-direction>` values	Description
`in`	Incoming updates.
`out`	Outgoing updates.

access-list¶

Access-list name.

access-list ACCESS-LIST

ACCESS-LIST

Access list name.

prefix-list¶

Prefix-list name.

prefix-list PREFIX-LIST

PREFIX-LIST

Prefix list name.

offset-list¶

Offset-list to modify route metric.

vsr running config# vrf <vrf> routing ripng
vsr running ripng# offset-list <interface> <update-direction> metric <0-16> \
... access-list ACCESS-LIST

`<interface>` values	Description
`<ifname>{1,15}`	An interface name.
`all`	Match all interfaces.

`<update-direction>` values	Description
`in`	Incoming updates.
`out`	Outgoing updates.

metric (mandatory)¶

Route metric.

metric <0-16>

access-list (mandatory)¶

Access-list name.

access-list ACCESS-LIST

ACCESS-LIST

Access list name.

state (state only)¶

Operational RIPng state data.

route (state only)¶

RIPng IPv6 route state.

protocol (state only)¶

Route protocol.

vsr> show state vrf <vrf> routing ripng state route <route> protocol

route-type (state only)¶

Route type.

vsr> show state vrf <vrf> routing ripng state route <route> route-type

nexthop (state only)¶

Nexthop IPv6 address.

vsr> show state vrf <vrf> routing ripng state route <route> nexthop

metric (state only)¶

Route metric.

vsr> show state vrf <vrf> routing ripng state route <route> metric

neighbor (state only)¶

RIP neighbor state.

last-update (state only)¶

The time when the most recent RIP update was received from this neighbor.

vsr> show state vrf <vrf> routing ripng state neighbor <neighbor> last-update

bad-packets-received (state only)¶

The number of RIP invalid packets received from this neighbor which were subsequently discarded for any reason (e.g. a version 0 packet, or an unknown command type).

vsr> show state vrf <vrf> routing ripng state neighbor <neighbor> bad-packets-received

bad-routes-received (state only)¶

The number of routes received from this neighbor, in valid RIP packets, which were ignored for any reason (e.g. unknown address family, or invalid metric).

vsr> show state vrf <vrf> routing ripng state neighbor <neighbor> bad-routes-received