rip¶
RIP router configuration.
vrouter running config# vrf <vrf> routing rip
neighbor¶
Specifies the RIP neighbors. Useful for a non-broadcast multiple access (NBMA) network.
vrouter running config# vrf <vrf> routing rip
vrouter running rip# neighbor NEIGHBOR
NEIGHBOR |
An IPv4 address. |
static-route¶
RIP static routes.
vrouter running config# vrf <vrf> routing rip
vrouter running rip# static-route STATIC-ROUTE
STATIC-ROUTE |
An IPv4 prefix: address and CIDR mask. |
enabled¶
Enable or disable router.
vrouter running config# vrf <vrf> routing rip
vrouter running rip# enabled true|false
- Default value
true
allow-ecmp¶
Allow equal-cost multi-path.
vrouter running config# vrf <vrf> routing rip
vrouter running rip# allow-ecmp true|false
- Default value
false
default-information-originate¶
Control distribution of default route.
vrouter running config# vrf <vrf> routing rip
vrouter running rip# default-information-originate true|false
- Default value
false
default-metric¶
Default metric of redistributed routes.
vrouter running config# vrf <vrf> routing rip
vrouter running rip# default-metric <uint8>
- Default value
1
network¶
Enable RIP on the specified IP network.
vrouter running config# vrf <vrf> routing rip
vrouter running rip# network NETWORK
|
Description |
|---|---|
<A.B.C.D/M> |
An IPv4 prefix: address and CIDR mask. |
<X:X::X:X/M> |
An IPv6 prefix: address and CIDR mask. |
interface¶
Enable RIP on the specified interface.
vrouter running config# vrf <vrf> routing rip
vrouter running rip# interface INTERFACE
INTERFACE |
An interface name. |
passive-interface¶
A list of interfaces where the sending of RIP packets is disabled.
vrouter running config# vrf <vrf> routing rip
vrouter running rip# passive-interface PASSIVE-INTERFACE
PASSIVE-INTERFACE |
An interface name. |
administrative-distance¶
Administrative distance.
vrouter running config# vrf <vrf> routing rip administrative-distance
default¶
Default administrative distance.
vrouter running config# vrf <vrf> routing rip administrative-distance
vrouter running administrative-distance# default <uint8>
source¶
Custom administrative distance per IP prefix.
vrouter running config# vrf <vrf> routing rip administrative-distance
vrouter running administrative-distance# source <source> distance <uint8> \
... access-list ACCESS-LIST
<source> |
An IPv4 prefix: address and CIDR mask. |
redistribute¶
Redistributes routes learned from other routing protocols.
vrouter running config# vrf <vrf> routing rip
vrouter running rip# redistribute <redistribute> metric <uint8> route-map ROUTE-MAP
|
Description |
|---|---|
connected |
Connected routes (directly attached subnet or host). |
kernel |
Kernel routes (not installed via the zebra RIB). |
ospf |
Open Shortest Path First (OSPFv2). |
bgp |
Border Gateway Protocol (BGP). |
static |
Statically configured routes. |
metric¶
Metric used for the redistributed route. If a metric is not specified, the metric configured with the default-metric attribute in RIP router configuration is used. If the default-metric attribute has not been configured, the default metric for redistributed routes is 0.
metric <uint8>
route-map¶
Applies the conditions of the specified route-map to routes that are redistributed into the RIP routing instance.
route-map ROUTE-MAP
ROUTE-MAP |
Route map name. |
route-map¶
Apply route map to this neighbor.
vrouter running config# vrf <vrf> routing rip
vrouter running rip# route-map <interface> <route-direction> route-map-name ROUTE-MAP-NAME
<interface> |
An interface name. |
|
Description |
|---|---|
in |
Apply map to incoming routes. |
out |
Apply map to outbound routes. |
route-map-name (mandatory)¶
Route-map name.
route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME |
Route map name. |
timers¶
Settings of basic timers.
vrouter running config# vrf <vrf> routing rip timers
flush-interval¶
Interval before a route is flushed from the routing table.
vrouter running config# vrf <vrf> routing rip timers
vrouter running timers# flush-interval <uint32>
- Default value
120
holddown-interval¶
Interval before better routes are released.
vrouter running config# vrf <vrf> routing rip timers
vrouter running timers# holddown-interval <uint32>
- Default value
180
update-interval¶
Interval at which RIP updates are sent.
vrouter running config# vrf <vrf> routing rip timers
vrouter running timers# update-interval <uint32>
- Default value
30
version¶
Set routing protocol version.
vrouter running config# vrf <vrf> routing rip version
receive¶
Advertisement reception - Version control.
vrouter running config# vrf <vrf> routing rip version
vrouter running version# receive RECEIVE
|
Description |
|---|---|
1 |
Accept RIPv1 updates only. |
2 |
Accept RIPv2 updates only. |
1-2 |
Accept both RIPv1 and RIPv2 updates. |
- Default value
1-2
send¶
Advertisement transmission - Version control.
vrouter running config# vrf <vrf> routing rip version
vrouter running version# send SEND
|
Description |
|---|---|
1 |
Send RIPv1 updates only. |
2 |
Send RIPv2 updates only. |
- Default value
2
distribute-list¶
Filter networks in routing updates.
vrouter running config# vrf <vrf> routing rip
vrouter running rip# distribute-list <interface> <update-direction> access-list ACCESS-LIST \
... prefix-list PREFIX-LIST
|
Description |
|---|---|
<ifname> |
An interface name. |
all |
Match all interfaces. |
|
Description |
|---|---|
in |
Incoming updates. |
out |
Outgoing updates. |
offset-list¶
Offset-list to modify route metric.
vrouter running config# vrf <vrf> routing rip
vrouter running rip# offset-list <interface> <update-direction> metric <uint8> \
... access-list ACCESS-LIST
|
Description |
|---|---|
<ifname> |
An interface name. |
all |
Match all interfaces. |
|
Description |
|---|---|
in |
Incoming updates. |
out |
Outgoing updates. |
state (state only)¶
Operational RIP state data.
route (state only)¶
RIP IPv4 route state.
protocol (state only)¶
Route protocol.
vrouter> show state vrf <vrf> routing rip state route <route> protocol
route-type (state only)¶
Route type.
vrouter> show state vrf <vrf> routing rip state route <route> route-type
nexthop (state only)¶
Nexthop IPv4 address.
vrouter> show state vrf <vrf> routing rip state route <route> nexthop
interface (state only)¶
The interface that the route uses.
vrouter> show state vrf <vrf> routing rip state route <route> interface
metric (state only)¶
Route metric.
vrouter> show state vrf <vrf> routing rip state route <route> metric
neighbor (state only)¶
RIP neighbor state.
last-update (state only)¶
The time when the most recent RIP update was received from this neighbor.
vrouter> show state vrf <vrf> routing rip state neighbor <neighbor> last-update
bad-packets-received (state only)¶
The number of RIP invalid packets received from this neighbor which were subsequently discarded for any reason (e.g. a version 0 packet, or an unknown command type).
vrouter> show state vrf <vrf> routing rip state neighbor <neighbor> bad-packets-received
bad-routes-received (state only)¶
The number of routes received from this neighbor, in valid RIP packets, which were ignored for any reason (e.g. unknown address family, or invalid metric).
vrouter> show state vrf <vrf> routing rip state neighbor <neighbor> bad-routes-received