vxlan

Note

requires a Product License.

The list of VxLAN interfaces on the device.

vsr running config# vrf <vrf> interface vxlan <vxlan>

<vxlan>

An interface name.

mtu

Set the max transmission unit size in octets.

vsr running config# vrf <vrf> interface vxlan <vxlan>
vsr running vxlan <vxlan># mtu <uint32>

promiscuous

Set promiscuous mode.

vsr running config# vrf <vrf> interface vxlan <vxlan>
vsr running vxlan <vxlan># promiscuous true|false

enabled (pushed)

The desired (administrative) state of the interface.

vsr running config# vrf <vrf> interface vxlan <vxlan>
vsr running vxlan <vxlan># enabled true|false
Default value
true

description

A textual description of the interface.

vsr running config# vrf <vrf> interface vxlan <vxlan>
vsr running vxlan <vxlan># description <string>

vni (mandatory)

Interface VXLAN Network ID. This ID must be unique.

vsr running config# vrf <vrf> interface vxlan <vxlan>
vsr running vxlan <vxlan># vni VNI

VNI

Type definition representing VXLAN Segment ID / VXLAN Network Identifier value.

group

The group multicast IP address.

vsr running config# vrf <vrf> interface vxlan <vxlan>
vsr running vxlan <vxlan># group GROUP

GROUP

An IPv4 or IPv6 multicast address.

remote

The remote IP address, which is no a multicast group.

vsr running config# vrf <vrf> interface vxlan <vxlan>
vsr running vxlan <vxlan># remote REMOTE

REMOTE

An IPv4 or IPv6 address which is not a multicast group.

local

The source address that should be used for the Vxlan tunnel. If none is specified an address of the link interface will be used.

vsr running config# vrf <vrf> interface vxlan <vxlan>
vsr running vxlan <vxlan># local LOCAL

LOCAL

An IPv4 or IPv6 address.

ttl

The time-to-live (or hop limit) that should be utilised for the IP packets used for the tunnel transport. If not set, the ttl is inherited from the inner packet for IPv4 tunnels, and is 64 for IPv6 tunnels.

vsr running config# vrf <vrf> interface vxlan <vxlan>
vsr running vxlan <vxlan># ttl <uint8>

tos

Set the DSCP bits in the Type of Service field.

vsr running config# vrf <vrf> interface vxlan <vxlan>
vsr running vxlan <vxlan># tos TOS

TOS values

Description

<uint8>

No description.

inherit

Inherit the ToS from inner frame.

learning

Enable the registration of unknown source link layer addresses and IP addresses into the VxLAN forwarding database.

vsr running config# vrf <vrf> interface vxlan <vxlan>
vsr running vxlan <vxlan># learning true|false
Default value
true

gbp

Enable the Group Policy extension.

vsr running config# vrf <vrf> interface vxlan <vxlan>
vsr running vxlan <vxlan># gbp true|false
Default value
false

dst

UDP destination port.

vsr running config# vrf <vrf> interface vxlan <vxlan>
vsr running vxlan <vxlan># dst <uint16>
Default value
4789

ifindex (state only)

System assigned number for each interface. Corresponds to ifIndex object in SNMP Interface MIB.

vsr> show state vrf <vrf> interface vxlan <vxlan> ifindex

admin-status (state only)

The desired state of the interface. In RFC 7223 this leaf has the same read semantics as ifAdminStatus. Here, it reflects the administrative state as set by enabling or disabling the interface.

vsr> show state vrf <vrf> interface vxlan <vxlan> admin-status

oper-status (state only)

The current operational state of the interface. This leaf has the same semantics as ifOperStatus.

vsr> show state vrf <vrf> interface vxlan <vxlan> oper-status

last-change (state only)

This timestamp indicates the time of the last state change of the interface (e.g., up-to-down transition). This corresponds to the ifLastChange object in the standard interface MIB. The value is the timestamp in nanoseconds relative to the Unix Epoch (Jan 1, 1970 00:00:00 UTC).

vsr> show state vrf <vrf> interface vxlan <vxlan> last-change

ipv4

Parameters for the IPv4 address family.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4

enabled

Controls whether IPv4 is enabled or disabled on this interface. When IPv4 is enabled, this interface is connected to an IPv4 stack, and the interface can send and receive IPv4 packets.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4
vsr running ipv4# enabled true|false
Default value
true

address

The list of configured IPv4 addresses on the interface.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4
vsr running ipv4# address <address> peer PEER

<address> values

Description

<ipv4-address>

An IPv4 address.

<masked-ipv4-address>

A masked IPv4 address: address and prefix of that subnet.

peer

The IPv4 address of the remote endpoint for point to point interfaces.

peer PEER

PEER

An IPv4 address.

origin (state only)

The origin of this address, e.g., statically configured, assigned by DHCP, etc..

vsr> show state vrf <vrf> interface vxlan <vxlan> ipv4 address <address> origin

neighbor

A list of mappings from IPv4 addresses to link-layer addresses. Entries in this list are used as static entries in the ARP Cache.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4
vsr running ipv4# neighbor <neighbor> link-layer-address LINK-LAYER-ADDRESS

<neighbor>

An IPv4 address.

state (state only)

The state of this neighbor entry.

vsr> show state vrf <vrf> interface vxlan <vxlan> ipv4 neighbor <neighbor> state

dhcp

DHCP client configuration.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4 dhcp

enabled

Enable or disable DHCP.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4 dhcp
vsr running dhcp# enabled true|false
Default value
true

timeout

Time before deciding that it’s not going to be able to contact a server.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4 dhcp
vsr running dhcp# timeout <uint32>
Default value
60

retry

Time before trying again to contact a DHCP server.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4 dhcp
vsr running dhcp# retry <uint32>
Default value
300

select-timeout

Time at which the client stops waiting for other offers from servers.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4 dhcp
vsr running dhcp# select-timeout <uint32>
Default value
0

reboot

Time after trying to reacquire its old address before trying to discover a new address.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4 dhcp
vsr running dhcp# reboot <uint32>
Default value
10

initial-interval

Time between the first attempt to reach a server and the second attempt to reach a server.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4 dhcp
vsr running dhcp# initial-interval <uint32>
Default value
10

dhcp-lease-time

Requested lease time.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4 dhcp
vsr running dhcp# dhcp-lease-time <uint32>
Default value
7200

dhcp-client-identifier-ascii

DHCP client identifier (ASCII).

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4 dhcp
vsr running dhcp# dhcp-client-identifier-ascii <string>

dhcp-client-identifier-hexa

DHCP client identifier (hexadecimal).

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4 dhcp
vsr running dhcp# dhcp-client-identifier-hexa <string>

host-name

DHCP client name.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4 dhcp
vsr running dhcp# host-name <string>

request

DHCP requests.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4 dhcp
vsr running dhcp# request REQUEST

REQUEST

Available DHCP requests.

Default value
subnet-mask
broadcast-address
time-offset
routers
domain-name
domain-search
domain-name-servers
host-name
nis-domain
nis-servers
ntp-servers
interface-mtu

current-lease (state only)

Current lease.

fixed-address (state only)

The IPv4 address on the interface.

vsr> show state vrf <vrf> interface vxlan <vxlan> ipv4 dhcp current-lease fixed-address
renew (state only)

Time at which the client should begin trying to contact its server to renew its lease.

vsr> show state vrf <vrf> interface vxlan <vxlan> ipv4 dhcp current-lease renew
rebind (state only)

Time at which the client should begin to try to contact any dhcp server to renew its lease.

vsr> show state vrf <vrf> interface vxlan <vxlan> ipv4 dhcp current-lease rebind
expire (state only)

Time at which the client must stop using a lease if it has not been able to renew it.

vsr> show state vrf <vrf> interface vxlan <vxlan> ipv4 dhcp current-lease expire

fdb

IPv4 FDB configuration.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv4
vsr running ipv4# fdb link-layer-address <link-layer-address> ip <ip> link-interface LINK-INTERFACE \
... port PORT vni VNI

<link-layer-address>

An IEEE 802 MAC address.

<ip>

An IPv4 address.

port

The UDP destination PORT number to use to connect to the remote VXLAN tunnel endpoint (default: the VXLAN dst).

port PORT

PORT

A 16-bit port number used by a transport protocol such as TCP or UDP.

vni

The VXLAN VNI Network Identifier (or VXLAN Segment ID) to use to connect to the remote VXLAN tunnel endpoint (default: the VXLAN vni).

vni VNI

VNI

Type definition representing VXLAN Segment ID / VXLAN Network Identifier value.

state (state only)

FDB operational state.

vsr> show state vrf <vrf> interface vxlan <vxlan> ipv4 fdb link-layer-address <link-layer-address> ip <ip> state

ethernet

Top-level container for Ethernet configuration.

vsr running config# vrf <vrf> interface vxlan <vxlan> ethernet

mac-address

Assigns a MAC address to the Ethernet interface. If not specified, the corresponding operational state leaf is expected to show the system-assigned MAC address.

vsr running config# vrf <vrf> interface vxlan <vxlan> ethernet
vsr running ethernet# mac-address MAC-ADDRESS

MAC-ADDRESS

An IEEE 802 unicast MAC address i.e. the second digit is an even number. Moreover the mac address must not be 00:00:00:00:00:00.

ipv6

Parameters for the IPv6 address family.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv6

enabled

Controls whether IPv6 is enabled or disabled on this interface. When IPv6 is enabled, this interface is connected to an IPv6 stack, and the interface can send and receive IPv6 packets.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv6
vsr running ipv6# enabled true|false
Default value
true

address

The list of configured IPv6 addresses on the interface.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv6
vsr running ipv6# address <address> peer PEER

<address> values

Description

<ipv6-address>

An IPv6 address.

<masked-ipv6-address>

A masked IPv6 address: address and prefix of that subnet.

peer

The IPv6 address of the remote endpoint for point to point interfaces.

peer PEER

PEER

An IPv6 address.

origin (state only)

The origin of this address, e.g., static, dhcp, etc.

vsr> show state vrf <vrf> interface vxlan <vxlan> ipv6 address <address> origin

status (state only)

The status of an address. Most of the states correspond to states from the IPv6 Stateless Address Autoconfiguration protocol.

vsr> show state vrf <vrf> interface vxlan <vxlan> ipv6 address <address> status

neighbor

List of IPv6 neighbors.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv6
vsr running ipv6# neighbor <neighbor> link-layer-address LINK-LAYER-ADDRESS

<neighbor>

An IPv6 address.

router (state only)

Indicates that the neighbor node acts as a router.

vsr> show state vrf <vrf> interface vxlan <vxlan> ipv6 neighbor <neighbor> router

state (state only)

The state of this neighbor entry.

vsr> show state vrf <vrf> interface vxlan <vxlan> ipv6 neighbor <neighbor> state

fdb

IPv6 FDB configuration.

vsr running config# vrf <vrf> interface vxlan <vxlan> ipv6
vsr running ipv6# fdb link-layer-address <link-layer-address> ip <ip> link-interface LINK-INTERFACE \
... port PORT vni VNI

<link-layer-address>

An IEEE 802 MAC address.

<ip>

An IPv6 address.

port

The UDP destination PORT number to use to connect to the remote VXLAN tunnel endpoint (default: the VXLAN dst).

port PORT

PORT

A 16-bit port number used by a transport protocol such as TCP or UDP.

vni

The VXLAN VNI Network Identifier (or VXLAN Segment ID) to use to connect to the remote VXLAN tunnel endpoint (default: the VXLAN vni).

vni VNI

VNI

Type definition representing VXLAN Segment ID / VXLAN Network Identifier value.

state (state only)

FDB operational state.

vsr> show state vrf <vrf> interface vxlan <vxlan> ipv6 fdb link-layer-address <link-layer-address> ip <ip> state

network-stack

Network stack parameters for this interface.

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack

ipv4

IPv4 parameters.

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack ipv4

send-redirects

Send ICMP redirect if host is on the same network than gateway.

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack ipv4
vsr running ipv4# send-redirects true|false

accept-redirects

Accept redirect when acting as a host. It is always disabled when acting as a router. Must be activated at vrf or system level too to be activated.

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack ipv4
vsr running ipv4# accept-redirects true|false

accept-source-route

Accept packets with source route option. Must be activated at vrf or system level too to be activated.

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack ipv4
vsr running ipv4# accept-source-route true|false

arp-announce

Define different restriction levels for announcing the local source IP address from IP packets in ARP requests sent on interface. Increasing the restriction level gives more chance for receiving answer from the resolved target while decreasing the level announces more valid sender’s information.

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack ipv4
vsr running ipv4# arp-announce ARP-ANNOUNCE

ARP-ANNOUNCE values

Description

any

Use any local address, configured on any interface.

avoid-not-in-subnet

Try to avoid local addresses that are not in the target’s subnet for this interface. This mode is useful when target hosts reachable via this interface require the source IP address in ARP requests to be part of their logical network configured on the receiving interface. When we generate the request we will check all our subnets that include the target IP and will preserve the source address if it is from such subnet. If there is no such subnet we select source address according to the rules for level 2, ‘best-local’.

best-local

Always use the best local address for this target. In this mode we ignore the source address in the IP packet and try to select local address that we prefer for talks with the target host. Such local address is selected by looking for primary IP addresses on all our subnets on the outgoing interface that include the target IP address. If no suitable local address is found we select the first local address we have on the outgoing interface or on all other interfaces, with the hope we will receive reply for our request and even sometimes no matter the source IP address we announce.

arp-filter

Allows to have multiple network interfaces on the same subnet, and have the ARPs for each interface be answered based on whether or not the kernel would route a packet from the ARP’d IP out that interface (therefore you must use source based routing for this to work). In other words it allows control of which cards (usually 1) will respond to an arp request.

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack ipv4
vsr running ipv4# arp-filter true|false

arp-ignore

Define different modes for sending replies in response to received ARP requests that resolve local target IP addresses.

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack ipv4
vsr running ipv4# arp-ignore ARP-IGNORE

ARP-IGNORE values

Description

any

Reply for any local target IP address, configured on any interface.

check-interface

Reply only if the target IP address is local address configured on the incoming interface.

check-interface-and-subnet

Reply only if the target IP address is local address configured on the incoming interface and both with the sender’s IP address are part from same subnet on this interface.

ignore-scope

Do not reply for local addresses configured with scope host, only resolutions for global and link addresses are replied.

ignore-all

Do not reply for all local addresses.

arp-proxy

Enable ARP proxy.

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack ipv4
vsr running ipv4# arp-proxy true|false

log-invalid-addresses

Log packets with impossible addresses.

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack ipv4
vsr running ipv4# log-invalid-addresses true|false

ipv6

IPv6 parameters.

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack ipv6

autoconfiguration

Autoconfigure addresses using Prefix Information in Router Advertisements.

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack ipv6
vsr running ipv6# autoconfiguration true|false

accept-router-advert

Accept Router Advertisements.

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack ipv6
vsr running ipv6# accept-router-advert ACCEPT-ROUTER-ADVERT

ACCEPT-ROUTER-ADVERT values

Description

never

Do not accept Router Advertisements.

norouter-mode

Accept Router Advertisements if forwarding is disabled.

always

Accept Router Advertisements even if forwarding is enabled.

accept-redirects

Accept redirect when acting as a host. It is always disabled when acting as a router.

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack ipv6
vsr running ipv6# accept-redirects true|false

accept-source-route

Accept packets with source route option.

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack ipv6
vsr running ipv6# accept-source-route true|false

router-solicitations

Number of Router Solicitations to send until assuming no routers are present.

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack ipv6
vsr running ipv6# router-solicitations <int16>

use-temporary-addresses

Preference for Privacy Extensions (RFC4941). Not applied to point-to- point and loopback devices (always 0).

vsr running config# vrf <vrf> interface vxlan <vxlan> network-stack ipv6
vsr running ipv6# use-temporary-addresses USE-TEMPORARY-ADDRESSES

USE-TEMPORARY-ADDRESSES values

Description

never

Disable Privacy Extensions, i.e. use the public address, subnet prefix/interface id, where interface id is always the same.

prefer-public-addresses

Enable Privacy Extensions, but prefer public addresses over temporary addresses.

always

Enable Privacy Extensions and prefer temporary addresses over public addresses.

src-range

Range of UDP source ports.

vsr running config# vrf <vrf> interface vxlan <vxlan> src-range

<uint16>

Minimal value of source port range.

vsr running config# vrf <vrf> interface vxlan <vxlan> src-range
vsr running src-range# <uint16>
Default value
49152

<uint16>

Maximal value of source port range.

vsr running config# vrf <vrf> interface vxlan <vxlan> src-range
vsr running src-range# <uint16>
Default value
65535

qos

Note

requires a Product License.

QoS configuration.

vsr running config# vrf <vrf> interface vxlan <vxlan> qos

ingress

Ingress QoS configuration.

vsr running config# vrf <vrf> interface vxlan <vxlan> qos ingress

rate-limit

Rate limit configuration.

vsr running config# vrf <vrf> interface vxlan <vxlan> qos ingress rate-limit
policer (config only)

Traffic policer defined in the QoS context.

vsr running config# vrf <vrf> interface vxlan <vxlan> qos ingress rate-limit
vsr running rate-limit# policer <leafref>
shared-policer (config only)

Traffic shared policer defined in the QoS context.

vsr running config# vrf <vrf> interface vxlan <vxlan> qos ingress rate-limit
vsr running rate-limit# shared-policer <leafref>
policer (state only)

Traffic policer.

bandwidth (state only)

Maximum bandwidth of regular traffic, a.k.a. CIR (Committed Information Rate), in bps. 0 allows no regular traffic.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos ingress rate-limit policer bandwidth
burst (state only)

Maximum burst size of shaped traffic, a.k.a. CBS (Committed Burst Size), in bytes. The default value is set to bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos ingress rate-limit policer burst
excess-bandwidth (state only)

Maximum bandwidth of excess traffic, a.k.a. EIR (Excess Information Rate), in bps. 0 allows no excess traffic.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos ingress rate-limit policer excess-bandwidth
excess-burst (state only)

Maximum burst size of excess traffic, a.k.a. EBS (Excess Burst Size), in bytes. The default value is set to excess-bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos ingress rate-limit policer excess-burst
shared-policer (state only)

Shared policer name.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos ingress rate-limit policer shared-policer
stats (state only)

Traffic policer statistics.

pass-packets (state only)

Number of packets passed (regular traffic that conforms to (bandwidth, burst) specification.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos ingress rate-limit policer stats pass-packets
pass-bytes (state only)

Number of bytes passed (regular traffic that conforms to (bandwidth, burst) specification.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos ingress rate-limit policer stats pass-bytes
pass-excess-packets (state only)

Number of excess packets passed (excess traffic that conforms to (excess-bandwidth, excess-burst) specification.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos ingress rate-limit policer stats pass-excess-packets
pass-excess-bytes (state only)

Number of excess bytes passed (excess traffic that conforms to (excess-bandwidth, excess-burst) specification.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos ingress rate-limit policer stats pass-excess-bytes
drop-packets (state only)

Number of packets dropped (traffic that does not conform to bandwidth or excess-bandwidth).

vsr> show state vrf <vrf> interface vxlan <vxlan> qos ingress rate-limit policer stats drop-packets
drop-bytes (state only)

Number of bytes dropped (traffic that does not conform to bandwidth or excess-bandwidth).

vsr> show state vrf <vrf> interface vxlan <vxlan> qos ingress rate-limit policer stats drop-bytes

egress

Egress QoS configuration.

vsr running config# vrf <vrf> interface vxlan <vxlan> qos egress

rate-limit

Rate limit configuration.

vsr running config# vrf <vrf> interface vxlan <vxlan> qos egress rate-limit
policer (config only)

Traffic policer defined in the QoS context.

vsr running config# vrf <vrf> interface vxlan <vxlan> qos egress rate-limit
vsr running rate-limit# policer <leafref>
shared-policer (config only)

Traffic shared policer defined in the QoS context.

vsr running config# vrf <vrf> interface vxlan <vxlan> qos egress rate-limit
vsr running rate-limit# shared-policer <leafref>
policer (state only)

Traffic policer.

bandwidth (state only)

Maximum bandwidth of regular traffic, a.k.a. CIR (Committed Information Rate), in bps. 0 allows no regular traffic.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos egress rate-limit policer bandwidth
burst (state only)

Maximum burst size of shaped traffic, a.k.a. CBS (Committed Burst Size), in bytes. The default value is set to bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos egress rate-limit policer burst
excess-bandwidth (state only)

Maximum bandwidth of excess traffic, a.k.a. EIR (Excess Information Rate), in bps. 0 allows no excess traffic.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos egress rate-limit policer excess-bandwidth
excess-burst (state only)

Maximum burst size of excess traffic, a.k.a. EBS (Excess Burst Size), in bytes. The default value is set to excess-bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos egress rate-limit policer excess-burst
shared-policer (state only)

Shared policer name.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos egress rate-limit policer shared-policer
stats (state only)

Traffic policer statistics.

pass-packets (state only)

Number of packets passed (regular traffic that conforms to (bandwidth, burst) specification.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos egress rate-limit policer stats pass-packets
pass-bytes (state only)

Number of bytes passed (regular traffic that conforms to (bandwidth, burst) specification.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos egress rate-limit policer stats pass-bytes
pass-excess-packets (state only)

Number of excess packets passed (excess traffic that conforms to (excess-bandwidth, excess-burst) specification.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos egress rate-limit policer stats pass-excess-packets
pass-excess-bytes (state only)

Number of excess bytes passed (excess traffic that conforms to (excess-bandwidth, excess-burst) specification.

vsr> show state vrf <vrf> interface vxlan <vxlan> qos egress rate-limit policer stats pass-excess-bytes
drop-packets (state only)

Number of packets dropped (traffic that does not conform to bandwidth or excess-bandwidth).

vsr> show state vrf <vrf> interface vxlan <vxlan> qos egress rate-limit policer stats drop-packets
drop-bytes (state only)

Number of bytes dropped (traffic that does not conform to bandwidth or excess-bandwidth).

vsr> show state vrf <vrf> interface vxlan <vxlan> qos egress rate-limit policer stats drop-bytes

counters (state only)

A collection of interface-related statistics objects.

in-octets (state only)

The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ‘last-clear’.

vsr> show state vrf <vrf> interface vxlan <vxlan> counters in-octets

in-unicast-pkts (state only)

The number of packets, delivered by this sub-layer to a higher (sub-)layer, that were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ‘last-clear’.

vsr> show state vrf <vrf> interface vxlan <vxlan> counters in-unicast-pkts

in-discards (state only)

The number of inbound packets that were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ‘last-clear’.

vsr> show state vrf <vrf> interface vxlan <vxlan> counters in-discards

in-errors (state only)

For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher- layer protocol. For character- oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of ‘last-clear’.

vsr> show state vrf <vrf> interface vxlan <vxlan> counters in-errors

out-octets (state only)

The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ‘last-clear’.

vsr> show state vrf <vrf> interface vxlan <vxlan> counters out-octets

out-unicast-pkts (state only)

The total number of packets that higher-level protocols requested be transmitted, and that were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of ‘last-clear’.

vsr> show state vrf <vrf> interface vxlan <vxlan> counters out-unicast-pkts

out-discards (state only)

The number of outbound packets that were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ‘last-clear’.

vsr> show state vrf <vrf> interface vxlan <vxlan> counters out-discards

out-errors (state only)

For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ‘last-clear’.

vsr> show state vrf <vrf> interface vxlan <vxlan> counters out-errors