ripng

Note

requires a Turbo Router Network License.

RIPng router configuration.

vrouter running config# vrf <vrf> routing ripng

aggregate

Set aggregate RIPng route announcement.

vrouter running config# vrf <vrf> routing ripng
vrouter running ripng# aggregate AGGREGATE

AGGREGATE

An IPv6 prefix: address and CIDR mask.

static-route

RIPng static routes.

vrouter running config# vrf <vrf> routing ripng
vrouter running ripng# static-route STATIC-ROUTE

STATIC-ROUTE

An IPv6 prefix: address and CIDR mask.

enabled

Enable or disable router.

vrouter running config# vrf <vrf> routing ripng
vrouter running ripng# enabled true|false
Default value
true

allow-ecmp

Allow equal-cost multi-path.

vrouter running config# vrf <vrf> routing ripng
vrouter running ripng# allow-ecmp true|false
Default value
false

default-information-originate

Control distribution of default route.

vrouter running config# vrf <vrf> routing ripng
vrouter running ripng# default-information-originate true|false
Default value
false

default-metric

Default metric of redistributed routes.

vrouter running config# vrf <vrf> routing ripng
vrouter running ripng# default-metric <uint8>
Default value
1

network

Enable RIP on the specified IP network.

vrouter running config# vrf <vrf> routing ripng
vrouter running ripng# network NETWORK

NETWORK values

Description

<A.B.C.D/M>

An IPv4 prefix: address and CIDR mask.

<X:X::X:X/M>

An IPv6 prefix: address and CIDR mask.

interface

Enable RIP on the specified interface.

vrouter running config# vrf <vrf> routing ripng
vrouter running ripng# interface INTERFACE

INTERFACE

An interface name.

passive-interface

A list of interfaces where the sending of RIP packets is disabled.

vrouter running config# vrf <vrf> routing ripng
vrouter running ripng# passive-interface PASSIVE-INTERFACE

PASSIVE-INTERFACE

An interface name.

redistribute

Redistributes routes learned from other routing protocols.

vrouter running config# vrf <vrf> routing ripng
vrouter running ripng# redistribute <redistribute> metric <uint8> route-map ROUTE-MAP

<redistribute> values

Description

connected

Connected routes (directly attached subnet or host).

kernel

Kernel routes (not installed via the zebra RIB).

ospf6

Open Shortest Path First (OSPFv3).

bgp

Border Gateway Protocol (BGP).

static

Statically configured routes.

metric

Metric used for the redistributed route. If a metric is not specified, the metric configured with the default-metric attribute in RIPng router configuration is used. If the default-metric attribute has not been configured, the default metric for redistributed routes is 0.

metric <uint8>

route-map

Applies the conditions of the specified route-map to routes that are redistributed into the RIPng routing instance.

route-map ROUTE-MAP

ROUTE-MAP

Route map name.

timers

Settings of basic timers.

vrouter running config# vrf <vrf> routing ripng timers

flush-interval

Interval before a route is flushed from the routing table.

vrouter running config# vrf <vrf> routing ripng timers
vrouter running timers# flush-interval <uint16>
Default value
120

holddown-interval

Interval before better routes are released.

vrouter running config# vrf <vrf> routing ripng timers
vrouter running timers# holddown-interval <uint16>
Default value
180

update-interval

Interval at which RIP updates are sent.

vrouter running config# vrf <vrf> routing ripng timers
vrouter running timers# update-interval <uint16>
Default value
30

distribute-list

Filter networks in routing updates.

vrouter running config# vrf <vrf> routing ripng
vrouter running ripng# distribute-list <interface> <update-direction> access-list ACCESS-LIST \
... prefix-list PREFIX-LIST

<interface> values

Description

<ifname>

An interface name.

all

Match all interfaces.

<update-direction> values

Description

in

Incoming updates.

out

Outgoing updates.

access-list

Access-list name.

access-list ACCESS-LIST

ACCESS-LIST

Access list name.

prefix-list

Prefix-list name.

prefix-list PREFIX-LIST

PREFIX-LIST

Prefix list name.

offset-list

Offset-list to modify route metric.

vrouter running config# vrf <vrf> routing ripng
vrouter running ripng# offset-list <interface> <update-direction> metric <uint8> \
... access-list ACCESS-LIST

<interface> values

Description

<ifname>

An interface name.

all

Match all interfaces.

<update-direction> values

Description

in

Incoming updates.

out

Outgoing updates.

metric (mandatory)

Route metric.

metric <uint8>

access-list (mandatory)

Access-list name.

access-list ACCESS-LIST

ACCESS-LIST

Access list name.

state (state only)

Operational RIPng state data.

route (state only)

RIPng IPv6 route state.

protocol (state only)

Route protocol.

vrouter> show state vrf <vrf> routing ripng state route <route> protocol

route-type (state only)

Route type.

vrouter> show state vrf <vrf> routing ripng state route <route> route-type

nexthop (state only)

Nexthop IPv6 address.

vrouter> show state vrf <vrf> routing ripng state route <route> nexthop

metric (state only)

Route metric.

vrouter> show state vrf <vrf> routing ripng state route <route> metric

neighbor (state only)

RIP neighbor state.

last-update (state only)

The time when the most recent RIP update was received from this neighbor.

vrouter> show state vrf <vrf> routing ripng state neighbor <neighbor> last-update

bad-packets-received (state only)

The number of RIP invalid packets received from this neighbor which were subsequently discarded for any reason (e.g. a version 0 packet, or an unknown command type).

vrouter> show state vrf <vrf> routing ripng state neighbor <neighbor> bad-packets-received

bad-routes-received (state only)

The number of routes received from this neighbor, in valid RIP packets, which were ignored for any reason (e.g. unknown address family, or invalid metric).

vrouter> show state vrf <vrf> routing ripng state neighbor <neighbor> bad-routes-received