Usage¶

In this section, it is assumed that Virtual Accelerator has been properly installed and configured. See Getting Started for more details.

With Linux - Fast Path Synchronization you can manage VXLANs via standard Linux commands.

Synchronizing Linux and the fast path¶

Load required modules:
```
# modprobe vxlan
```

Managing VXLANs from Linux¶

The Linux commands below allow you to manage VXLAN interfaces.

Creating a VXLAN interface¶

# ip link add IFNAME type vxlan id ID group GROUPADDR dev LINK_IFNAME ageing LIFETIME dstport DSTPORT

IFNAME: VXLAN interface’s name.
ID: VXLAN interface ID.
GROUPADDR: Multicast group address.
LINK_IFNAME: Name of the link interface.
DSTPORT: Port number of the VXLAN interface (IANA has assigned port 4789, but the Linux default value is 8472).
LIFETIME: Lifetime of FDB entries learnt.

Example

Create a new device (vxlan10). The device uses the multicast group 239.0.0.10 over eth1 to handle packets when no forwarding table entry matches. Lifetime of FDB entries learnt is 3600 seconds.

# ip link add vxlan10 type vxlan id 10 group 239.0.0.10 dev eth1 ageing 3600 dstport 4789

Creating a VXLAN GBP interface¶

# ip link add IFNAME type vxlan id ID group GROUPADDR dev LINK_IFNAME ageing LIFETIME dstport DSTPORT gbp

Example

Create a new VXLAN GBP device and set a mark in gbp field with iptables while forwarding.

# ip link add vxlan10 type vxlan id 10 group 239.0.0.10 dev eth1 ageing 3600 dstport 4789 gbp
# iptables -t mangle -A PREROUTING -j MARK --set-mark 0xabcd

Displaying information about a VXLAN interface¶

# ip -d link show vxlan10

Deleting a VXLAN device¶

# ip link delete vxlan10

Displaying the forwarding table¶

# bridge fdb show dev vxlan10

Creating a forwarding table entry¶

# bridge fdb add to 00:17:42:8a:b4:05 dst 192.168.1.1 dev vxlan10 permanent

Deleting a forwarding table entry¶

# bridge fdb delete 00:17:42:8a:b4:05 dev vxlan10

Managing VXLANs from the fast path¶

The fp-cli command below allows you to manage VXLAN instances from the fast path.

Displaying VXLAN interfaces¶

vxlan

Example

<fp-0> vxlan
VXLAN: check of rx checksum is off

vrfid: 0 dstport: 4789
        vxlan10-vr0 vni: 10
vrfid: 0 dstport: 8474 master: ovs

Note

VXLAN interfaces displaying ‘master: ovs’ will be managed by the Fast Path OVS Acceleration module. With kernel >= 4.4, a VXLAN interface will be created to represent Open vSwitch VXLAN ports.

Displaying a VXLAN interface’s FDB entries¶

vxlan-fdb <ifname>

ifname: Name of the VXLAN interface.

Example

<fp-0> vxlan-fdb vxlan10
vxlan10: vni=10 dstport=4789 ttl=255 srcminport=32768 srcmaxport=61000
FDB entries:
00:17:42:8a:b4:05 192.168.1.1 vni: 10 port: 4789
00:00:00:00:00:00 239.0.0.10 vni: 10 port: 4789 eth1-vr0

Enabling the verification of the UDP checksum on the input path¶

vxlan-check-rx-csum-set on|off

on|off: Enable or disable the verification of the UDP checksum on the input path.

Example

<fp-0> vxlan-check-rx-csum-set on
VXLAN: check of rx checksum is on (was off)

Statistics¶

vxlan-stats¶

Description

Display vxlan statistics.

Synopsis

vxlan-stats [percore] [all]

Parameters

percore: Display all statistics per core running the fast path.
all: Display all statistics (even those that are null).

Example

<fp-0> vxlan-stats all
 VxlanDroppedUnknownIface:0
 VxlanDroppedUnknownVNI:0
 VxlanDroppedHeaderTooShort:0
 VxlanDroppedInvalidIPv4Header:0
 VxlanDroppedInvalidIPv6Header:0
 VxlanDroppedInvalidIPv4Csum:0
 VxlanDroppedInvalidIPv6Csum:0
 VxlanDroppedOvsNoDst:0
 VxlanDroppedIPv4NoDst:0
 VxlanDroppedIPv6NoDst:0
 VxlanDroppedPrependOvsFailure:0
 VxlanDroppedPrependIPv4Failure:0
 VxlanDroppedPrependIPv6Failure:0
 VxlanDroppedInvalidIpFamily:0
 VxlanFdbForwDuplicateError:0
 VxlanDroppedAddGBPFailure:0
 VxlanExceptionIFlagNotSet:0
 VxlanExceptionOvsMtuExceeded:0
 VxlanExceptionIPv4MtuExceeded:0
 VxlanExceptionIPv6MtuExceeded:0
 VxlanExceptionNoInputFdb:0
 VxlanExceptionNoOutputFdb:0
 VxlanExceptionIPv4NoMcastSrc:0
 VxlanExceptionIPv6NoMcastSrc:0
 VxlanExceptionNoRemote:0
 VxlanExceptionOvsRoute:0
 VxlanExceptionIPv4Route:0
 VxlanExceptionIPv6Route:0
 VxlanExceptionTooManyFlags:0

vxlan-stats-json¶

Description

Display vxlan statistics in json format.

Synopsis

vxlan-stats-json

Example

<fp-0> vxlan-stats-json
 {
   "VxlanDroppedUnknownIface": 0,
   "VxlanDroppedInvalidIpFamily": 0,
   "VxlanDroppedUnknownVNI": 0,
   "VxlanDroppedPrependOvsFailure": 0,
   "VxlanDroppedPrependIPv4Failure": 0,
   "VxlanDroppedPrependIPv6Failure": 0,
   "VxlanDroppedOvsNoDst": 0,
   "VxlanDroppedIPv4NoDst": 0,
   "VxlanDroppedIPv6NoDst": 0,
   "VxlanDroppedHeaderTooShort": 0,
   "VxlanDroppedInvalidIPv4Header": 0,
   "VxlanDroppedInvalidIPv6Header": 0,
   "VxlanDroppedInvalidIPv4Csum": 0,
   "VxlanDroppedInvalidIPv6Csum": 0,
   "VxlanFdbForwDuplicateError": 0,
   "VxlanDroppedAddGBPFailure": 0,
   "VxlanExceptionNoInputFdb": 0,
   "VxlanExceptionNoOutputFdb": 0,
   "VxlanExceptionIPv4NoMcastSrc": 0,
   "VxlanExceptionIPv6NoMcastSrc": 0,
   "VxlanExceptionIFlagNotSet": 0,
   "VxlanExceptionTooManyFlags": 0,
   "VxlanExceptionOvsMtuExceeded": 0,
   "VxlanExceptionIPv4MtuExceeded": 0,
   "VxlanExceptionIPv6MtuExceeded": 0,
   "VxlanExceptionOvsRoute": 0,
   "VxlanExceptionIPv4Route": 0,
   "VxlanExceptionIPv6Route": 0,
   "VxlanExceptionNoRemote": 0,
 }

Providing options¶

--max-port¶

Maximum number of (VXLAN destination port, VR) pairs

Default value: 15
Memory footprint per (VXLAN destination port, VR) pair: 2 KB
Range: 0 .. 128

--max-if¶

Maximum number of VXLAN interfaces

Default value: 127
Memory footprint per VXLAN interface: 66 KB
Range: 0 .. 50K

--max-fdb¶

Maximum number of VXLAN forwarding database entries

Default value: 5000
Memory footprint per IPv6 Netfilter conntrack: 100 B
Range: 0 .. 50K

--port-hash-order¶

Size order of (VXLAN destination port, VR) tuples. Value automatically updated if --max-port is changed.

Default value: 4
Range: 1 .. 31

--if-hash-order¶

Size order of VXLAN interfaces hash table Value automatically updated if --max-if is changed.

Default value: 8
Range: 1 .. 31

--fdb-hash-order¶

Size order of VXLAN forwarding database hash table Value automatically updated if --max-fdb is changed.

Default value: 13
Range: 1 .. 31

Note

See Fast Path Capabilities documentation for impact of the available memory on the default value of configurable capabilities