bgp

BGP router configuration.

vrouter running config# vrf <vrf> routing bgp

enabled

Enable or disable BGP router.

vrouter running config# vrf <vrf> routing bgp
vrouter running bgp# enabled true|false
Default value
true

as (mandatory)

BGP AS number.

vrouter running config# vrf <vrf> routing bgp
vrouter running bgp# as AS
AS A numeric identifier for an autonomous system (AS). An AS is a single domain, under common administrative control, which forms a unit of routing policy. Autonomous systems can be assigned a 2-byte identifier, or a 4-byte identifier which may have public or private scope. Private ASNs are assigned from dedicated ranges. Public ASNs are assigned from ranges allocated by IANA to the regional internet registries (RIRs).

always-compare-med

If true, allow comparing MED from different neighbors.

vrouter running config# vrf <vrf> routing bgp
vrouter running bgp# always-compare-med true|false
Default value
false

cluster-id

Configure Route-Reflector Cluster-id.

vrouter running config# vrf <vrf> routing bgp
vrouter running bgp# cluster-id CLUSTER-ID
CLUSTER-ID values Description
<A.B.C.D> An IPv4 address.
<uint32> No description.

coalesce-time

Subgroup coalesce timer (in ms).

vrouter running config# vrf <vrf> routing bgp
vrouter running bgp# coalesce-time <uint32>

deterministic-med

If true, Pick the best-MED path among paths advertised from the neighboring AS.

vrouter running config# vrf <vrf> routing bgp
vrouter running bgp# deterministic-med true|false
Default value
false

ebgp-connected-route-check

Enable or disable checking if nexthop is connected on ebgp sessions.

vrouter running config# vrf <vrf> routing bgp
vrouter running bgp# ebgp-connected-route-check true|false
Default value
true

fast-external-failover

If true, immediately reset session if a link to a directly connected external peer goes down.

vrouter running config# vrf <vrf> routing bgp
vrouter running bgp# fast-external-failover true|false
Default value
true

graceful-shutdown

Enable or disable graceful shutdown.

vrouter running config# vrf <vrf> routing bgp
vrouter running bgp# graceful-shutdown true|false
Default value
false

log-neighbor-changes

If true, log neighbor up/down and reset reason.

vrouter running config# vrf <vrf> routing bgp
vrouter running bgp# log-neighbor-changes true|false
Default value
false

network-import-check

If true, check BGP network route exists in IGP.

vrouter running config# vrf <vrf> routing bgp
vrouter running bgp# network-import-check true|false
Default value
false

route-reflector-allow-outbound-policy

If true, allow modifications made by out route-map on IBGP neighbors.

vrouter running config# vrf <vrf> routing bgp
vrouter running bgp# route-reflector-allow-outbound-policy true|false
Default value
false

router-id

Router id of the router.

vrouter running config# vrf <vrf> routing bgp
vrouter running bgp# router-id ROUTER-ID
ROUTER-ID An IPv4 address.

neighbor-total-count (state only)

Total number of neighbors.

vrouter> show state vrf <vrf> routing bgp neighbor-total-count

bestpath

Change the default bestpath selection.

vrouter running config# vrf <vrf> routing bgp bestpath

compare-routerid

If true, compare router-id for identical EBGP paths.

vrouter running config# vrf <vrf> routing bgp bestpath
vrouter running bestpath# compare-routerid true|false
Default value
false

med

MED attribute.

vrouter running config# vrf <vrf> routing bgp bestpath
vrouter running bestpath# med MED
MED values Description
confederation Compare MED among confederation paths.
missing-as-worst Treat missing MED as the least preferred one.

as-path

AS-path attribute.

vrouter running config# vrf <vrf> routing bgp bestpath as-path

confederation

If true, compare path lengths including confederation sets and sequences in selecting a route.

vrouter running config# vrf <vrf> routing bgp bestpath as-path
vrouter running as-path# confederation true|false
Default value
false

ignore

If true, ignore as-path length in selecting a route.

vrouter running config# vrf <vrf> routing bgp bestpath as-path
vrouter running as-path# ignore true|false
Default value
false

multipath-relax

Allow load sharing across routes that have different AS paths (but same length).

vrouter running config# vrf <vrf> routing bgp bestpath as-path
vrouter running as-path# multipath-relax MULTIPATH-RELAX
MULTIPATH-RELAX values Description
as-set Generate an AS_SET.
no-as-set Do not generate an AS_SET.

client-to-client

BGP client to client route reflection.

vrouter running config# vrf <vrf> routing bgp client-to-client

reflection

Enable or disable BGP client to client route reflection.

vrouter running config# vrf <vrf> routing bgp client-to-client
vrouter running client-to-client# reflection true|false
Default value
true

confederation

Parameters indicating whether the local system acts as part of a BGP confederation.

vrouter running config# vrf <vrf> routing bgp confederation

identifier

Confederation AS number. Setting the AS indicates that the local-AS is part of a BGP confederation.

vrouter running config# vrf <vrf> routing bgp confederation
vrouter running confederation# identifier <uint32>

peers

Peer AS that are to be treated as part of the local confederation.

vrouter running config# vrf <vrf> routing bgp confederation
vrouter running confederation# peers <uint32>

dampening

Enable route-flap dampening.

vrouter running config# vrf <vrf> routing bgp dampening

half-life

Half-life time for the penalty (minutes).

vrouter running config# vrf <vrf> routing bgp dampening
vrouter running dampening# half-life <uint8>
Default value
15

reuse

Value to start reusing a route.

vrouter running config# vrf <vrf> routing bgp dampening
vrouter running dampening# reuse <uint16>
Default value
750

suppress

Value to start suppressing a route.

vrouter running config# vrf <vrf> routing bgp dampening
vrouter running dampening# suppress <uint16>
Default value
2000

max-suppress-time

Maximum duration to suppress a stable route (minutes).

vrouter running config# vrf <vrf> routing bgp dampening
vrouter running dampening# max-suppress-time <uint8>
Default value
60

graceful-restart

Configure graceful restart capability parameters.

vrouter running config# vrf <vrf> routing bgp graceful-restart

preserve-fw-state

If true, sets F-bit indication that fib is preserved while doing Graceful Restart.

vrouter running config# vrf <vrf> routing bgp graceful-restart
vrouter running graceful-restart# preserve-fw-state true|false
Default value
false

restart-time

Set the time to wait to delete stale routes before a BGP open message is received.

vrouter running config# vrf <vrf> routing bgp graceful-restart
vrouter running graceful-restart# restart-time <uint16>
Default value
120

stalepath-time

Set the max time to hold onto restarting peer’s stale paths.

vrouter running config# vrf <vrf> routing bgp graceful-restart
vrouter running graceful-restart# stalepath-time <uint16>
Default value
360

listen

Configure BGP listen options.

vrouter running config# vrf <vrf> routing bgp listen

limit

Maximum number of BGP Dynamic neighbors that can be created.

vrouter running config# vrf <vrf> routing bgp listen
vrouter running listen# limit <uint16>
Default value
100

neighbor-range

Configure BGP dynamic neighbors listen range.

vrouter running config# vrf <vrf> routing bgp listen
vrouter running listen# neighbor-range <neighbor-range> neighbor-group <neighbor-group>
<neighbor-range> values Description
<A.B.C.D/M> An IPv4 prefix: address and CIDR mask.
<X:X::X:X/M> An IPv6 prefix: address and CIDR mask.

neighbor-group (mandatory)

Neighbor group name.

neighbor-group <neighbor-group>

address (state only)

Neighbor address.

vrouter> show state vrf <vrf> routing bgp listen neighbor-range <neighbor-range> address

max-med

Advertise routes with max-med.

vrouter running config# vrf <vrf> routing bgp max-med

administrative

Administratively applied, for an indefinite period.

vrouter running config# vrf <vrf> routing bgp max-med
vrouter running max-med# administrative <uint32>

on-startup

Effective on a startup.

vrouter running config# vrf <vrf> routing bgp max-med on-startup

period (mandatory)

Time (seconds) period for max-med.

vrouter running config# vrf <vrf> routing bgp max-med on-startup
vrouter running on-startup# period <uint32>

max-med

Max MED value to be used.

vrouter running config# vrf <vrf> routing bgp max-med on-startup
vrouter running on-startup# max-med <uint32>
Default value
4294967295

packet-rw-quantum

Number of packets to read/write from peer socket per I/O cycle.

vrouter running config# vrf <vrf> routing bgp packet-rw-quantum

read

Number of packets to read from peer socket per I/O cycle.

vrouter running config# vrf <vrf> routing bgp packet-rw-quantum
vrouter running packet-rw-quantum# read <uint8>
Default value
10

write

Number of packets to write from peer socket per I/O cycle.

vrouter running config# vrf <vrf> routing bgp packet-rw-quantum
vrouter running packet-rw-quantum# write <uint8>
Default value
10

update-delay

Force initial delay for best-path and updates.

vrouter running config# vrf <vrf> routing bgp update-delay

delay

Force initial delay for best-path and updates.

vrouter running config# vrf <vrf> routing bgp update-delay
vrouter running update-delay# delay <uint16>
Default value
0

established-wait

Wait for peers to be established.

vrouter running config# vrf <vrf> routing bgp update-delay
vrouter running update-delay# established-wait <uint16>

address-family

Address-families associated with the BGP configuration.

vrouter running config# vrf <vrf> routing bgp address-family

ipv4-unicast

Configure IPv4 unicast address family.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast

table-map

BGP table to RIB route download filter.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast
vrouter running ipv4-unicast# table-map TABLE-MAP
TABLE-MAP Route map name.

enabled

Enable or disable IPv4 unicast addres family.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast
vrouter running ipv4-unicast# enabled true|false
Default value
true

dampening

Enable/Disable route-flap dampening in this address family.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast
vrouter running ipv4-unicast# dampening true|false
Default value
false

rib-count (state only)

Routing information base table count.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-unicast rib-count

neighbor-count (state only)

Number of neighbors for this address family.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-unicast neighbor-count

dynamic-neighbor-count (state only)

Number of dynamic neighbors for this address family.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-unicast dynamic-neighbor-count

network

Specify networks to announce via BGP.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast network <network>
<network> An IPv4 prefix: address and CIDR mask.
route-map

Route-map name.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast network <network>
vrouter running network <network># route-map ROUTE-MAP
ROUTE-MAP Route map name.
backdoor

If true, specify a BGP backdoor route.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast network <network>
vrouter running network <network># backdoor true|false
Default value
false
label-index

Label index to associate with the prefix.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast network <network>
vrouter running network <network># label-index <uint32>
ip-prefix (state only)

IPv4 prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-unicast network <network> ip-prefix
route (state only)

Route operational state.

validity (state only)

Route validity.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-unicast network <network> route <string> validity
route-type (state only)

Internal or external route.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-unicast network <network> route <string> route-type
prefix (state only)

Route prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-unicast network <network> route <string> prefix
prefix-length (state only)

Route prefix length.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-unicast network <network> route <string> prefix-length
med (state only)

Multi Exit Discriminator.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-unicast network <network> route <string> med
origin (state only)

Route origin.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-unicast network <network> route <string> origin
packet-length (state only)

Packet length.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-unicast network <network> route <string> packet-length
nexthop (state only)

Route nexthop.

used (state only)

Nexthop used.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-unicast network <network> route <string> nexthop <nexthop> used

redistribute

Redistribute information from another routing protocol.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast
vrouter running ipv4-unicast# redistribute <redistribute> id <uint32> metric <uint32> \
... route-map ROUTE-MAP
<redistribute> values Description
connected Connected routes (directly attached subnet or host).
kernel Kernel routes (not installed via the zebra RIB).
ospf Open Shortest Path First (OSPFv2).
rip Routing Information Protocol (RIP).
static Statically configured routes.
table Non-main Kernel Routing Table.
id

Instance or table ID.

id <uint32>
metric

Metric for redistributed routes.

metric <uint32>
route-map

Route-map name.

route-map ROUTE-MAP
ROUTE-MAP Route map name.
protocol (state only)

Routing protocol.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-unicast redistribute <redistribute> protocol

route-target

Route target list.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast route-target
redirect-import

Flow-spec redirect type route target, Import routes to this address- family.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast route-target
vrouter running route-target# redirect-import REDIRECT-IMPORT
REDIRECT-IMPORT values Description
<string> Extended communities or route-target attribute.
<string> Extended communities or route-target attribute.
<string> Extended communities or route-target attribute.

maximum-path

Forward packets over multiple paths.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast maximum-path
ebgp

Ebgp number of paths.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast maximum-path
vrouter running maximum-path# ebgp <uint8>
Default value
16
ibgp

Ibgp number of paths.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast maximum-path
vrouter running maximum-path# ibgp <uint8>
Default value
16
equal-cluster-length

If true, match the cluster length.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast maximum-path
vrouter running maximum-path# equal-cluster-length true|false
Default value
false

aggregate-address

Configure BGP aggregate entries.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast
vrouter running ipv4-unicast# aggregate-address <aggregate-address> as-set true|false \
... summary-only true|false
<aggregate-address> An IPv4 prefix: address and CIDR mask.
as-set

If true, generate AS set path information.

as-set true|false
Default value
false
summary-only

If true, filter more specific routes from updates.

summary-only true|false
Default value
false
ip-prefix (state only)

Aggregate prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-unicast aggregate-address <aggregate-address> ip-prefix

administrative-distance

Define administrative distance.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast
vrouter running ipv4-unicast# administrative-distance <administrative-distance> \
... distance <uint8> access-list ACCESS-LIST
<administrative-distance> An IPv4 prefix: address and CIDR mask.
distance (mandatory)

Administrative distance.

distance <uint8>
access-list

Access list name.

access-list ACCESS-LIST
ACCESS-LIST Access list name.
ip-prefix (state only)

IP source prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-unicast administrative-distance <administrative-distance> ip-prefix

bgp-distance

Configure BGP distance.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast bgp-distance
external-routes

Distance for routes external to the AS.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast bgp-distance
vrouter running bgp-distance# external-routes <uint8>
Default value
20
internal-routes

Distance for routes internal to the AS.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast bgp-distance
vrouter running bgp-distance# internal-routes <uint8>
Default value
200
local-routes

Distance for local routes.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-unicast bgp-distance
vrouter running bgp-distance# local-routes <uint8>
Default value
200

ipv4-multicast

Configure IPv4 multicast address family.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-multicast

table-map

BGP table to RIB route download filter.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-multicast
vrouter running ipv4-multicast# table-map TABLE-MAP
TABLE-MAP Route map name.

enabled

Enable or disable IPv4 multicast Address Family.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-multicast
vrouter running ipv4-multicast# enabled true|false
Default value
true

dampening

Enable/Disable route-flap dampening in this address family.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-multicast
vrouter running ipv4-multicast# dampening true|false
Default value
false

rib-count (state only)

Routing information base table count.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-multicast rib-count

neighbor-count (state only)

Number of neighbors for this address family.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-multicast neighbor-count

dynamic-neighbor-count (state only)

Number of dynamic neighbors for this address family.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-multicast dynamic-neighbor-count

network

Specify networks to announce via BGP.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-multicast network <network>
<network> An IPv4 prefix: address and CIDR mask.
route-map

Route-map name.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-multicast network <network>
vrouter running network <network># route-map ROUTE-MAP
ROUTE-MAP Route map name.
backdoor

If true, specify a BGP backdoor route.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-multicast network <network>
vrouter running network <network># backdoor true|false
Default value
false
label-index

Label index to associate with the prefix.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-multicast network <network>
vrouter running network <network># label-index <uint32>
ip-prefix (state only)

IPv4 prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-multicast network <network> ip-prefix
route (state only)

Route operational state.

validity (state only)

Route validity.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-multicast network <network> route <string> validity
route-type (state only)

Internal or external route.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-multicast network <network> route <string> route-type
prefix (state only)

Route prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-multicast network <network> route <string> prefix
prefix-length (state only)

Route prefix length.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-multicast network <network> route <string> prefix-length
med (state only)

Multi Exit Discriminator.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-multicast network <network> route <string> med
origin (state only)

Route origin.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-multicast network <network> route <string> origin
packet-length (state only)

Packet length.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-multicast network <network> route <string> packet-length
nexthop (state only)

Route nexthop.

used (state only)

Nexthop used.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-multicast network <network> route <string> nexthop <nexthop> used

aggregate-address

Configure BGP aggregate entries.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-multicast
vrouter running ipv4-multicast# aggregate-address <aggregate-address> as-set true|false \
... summary-only true|false
<aggregate-address> An IPv4 prefix: address and CIDR mask.
as-set

If true, generate AS set path information.

as-set true|false
Default value
false
summary-only

If true, filter more specific routes from updates.

summary-only true|false
Default value
false
ip-prefix (state only)

Aggregate prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-multicast aggregate-address <aggregate-address> ip-prefix

administrative-distance

Define administrative distance.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-multicast
vrouter running ipv4-multicast# administrative-distance <administrative-distance> \
... distance <uint8> access-list ACCESS-LIST
<administrative-distance> An IPv4 prefix: address and CIDR mask.
distance (mandatory)

Administrative distance.

distance <uint8>
access-list

Access list name.

access-list ACCESS-LIST
ACCESS-LIST Access list name.
ip-prefix (state only)

IP source prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-multicast administrative-distance <administrative-distance> ip-prefix

bgp-distance

Configure BGP distance.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-multicast bgp-distance
external-routes

Distance for routes external to the AS.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-multicast bgp-distance
vrouter running bgp-distance# external-routes <uint8>
Default value
20
internal-routes

Distance for routes internal to the AS.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-multicast bgp-distance
vrouter running bgp-distance# internal-routes <uint8>
Default value
200
local-routes

Distance for local routes.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-multicast bgp-distance
vrouter running bgp-distance# local-routes <uint8>
Default value
200

ipv4-flowspec

Configure IPv4 Flowspec address family.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-flowspec

enabled

Enable or disable IPv4 Flowspec Address Family.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-flowspec
vrouter running ipv4-flowspec# enabled true|false
Default value
true

local-install

Interface name.

vrouter running config# vrf <vrf> routing bgp address-family ipv4-flowspec
vrouter running ipv4-flowspec# local-install LOCAL-INSTALL
LOCAL-INSTALL An interface name.

rib-count (state only)

Routing information base table count.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-flowspec rib-count

neighbor-count (state only)

Number of neighbors for this address family.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-flowspec neighbor-count

dynamic-neighbor-count (state only)

Number of dynamic neighbors for this address family.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-flowspec dynamic-neighbor-count

route (state only)

Route operational state.

to (state only)

Route destination prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-flowspec route <uint32> to
from (state only)

Route source prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-flowspec route <uint32> from
peer-id (state only)

Route state identifier.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-flowspec route <uint32> peer-id
validity (state only)

Route validity.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-flowspec route <uint32> validity
route-type (state only)

Internal or external route.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-flowspec route <uint32> route-type
prefix (state only)

Route prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-flowspec route <uint32> prefix
prefix-length (state only)

Route prefix length.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-flowspec route <uint32> prefix-length
med (state only)

Multi Exit Discriminator.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-flowspec route <uint32> med
origin (state only)

Route origin.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-flowspec route <uint32> origin
packet-length (state only)

Packet length.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-flowspec route <uint32> packet-length
nexthop (state only)

Route nexthop.

used (state only)

Nexthop used.

vrouter> show state vrf <vrf> routing bgp address-family ipv4-flowspec route <uint32> nexthop <nexthop> used

ipv6-unicast

Configure IPv6 unicast address family.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast

table-map

BGP table to RIB route download filter.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast
vrouter running ipv6-unicast# table-map TABLE-MAP
TABLE-MAP Route map name.

enabled

Enable or disable IPv6 unicast Address Family.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast
vrouter running ipv6-unicast# enabled true|false
Default value
true

rib-count (state only)

Routing information base table count.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-unicast rib-count

neighbor-count (state only)

Number of neighbors for this address family.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-unicast neighbor-count

dynamic-neighbor-count (state only)

Number of dynamic neighbors for this address family.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-unicast dynamic-neighbor-count

network

Specify a network to announce via BGP.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast network <network>
<network> An IPv6 prefix: address and CIDR mask.
route-map

Route-map name.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast network <network>
vrouter running network <network># route-map ROUTE-MAP
ROUTE-MAP Route map name.
label-index

Label index to associate with the prefix.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast network <network>
vrouter running network <network># label-index <uint32>
ip-prefix (state only)

IPv6 prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-unicast network <network> ip-prefix
route (state only)

Route operational state.

validity (state only)

Route validity.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-unicast network <network> route <string> validity
route-type (state only)

Internal or external route.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-unicast network <network> route <string> route-type
prefix (state only)

Route prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-unicast network <network> route <string> prefix
prefix-length (state only)

Route prefix length.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-unicast network <network> route <string> prefix-length
med (state only)

Multi Exit Discriminator.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-unicast network <network> route <string> med
origin (state only)

Route origin.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-unicast network <network> route <string> origin
packet-length (state only)

Packet length.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-unicast network <network> route <string> packet-length
nexthop (state only)

Route nexthop.

used (state only)

Nexthop used.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-unicast network <network> route <string> nexthop <nexthop> used

aggregate-address

Configure BGP aggregate entries.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast
vrouter running ipv6-unicast# aggregate-address <aggregate-address> summary-only true|false
<aggregate-address> An IPv6 prefix: address and CIDR mask.
summary-only

If true, filter more specific routes from updates.

summary-only true|false
Default value
false
ip-prefix (state only)

Aggregate prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-unicast aggregate-address <aggregate-address> ip-prefix

redistribute

Redistribute information from another routing protocol.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast
vrouter running ipv6-unicast# redistribute <redistribute> metric <uint32> \
... route-map ROUTE-MAP
<redistribute> values Description
connected Connected routes (directly attached subnet or host).
kernel Kernel routes (not installed via the zebra RIB).
ospf6 Open Shortest Path First IPv6 (OSPFv3).
ripng Routing Information Protocol next-generation (IPv6) (RIPng).
static Statically configured routes.
table Non-main Kernel Routing Table.
metric

Metric for redistributed routes.

metric <uint32>
route-map

Route-map name.

route-map ROUTE-MAP
ROUTE-MAP Route map name.
protocol (state only)

Routing protocol.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-unicast redistribute <redistribute> protocol

administrative-distance

Define administrative distance.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast
vrouter running ipv6-unicast# administrative-distance <administrative-distance> \
... distance <uint8> access-list ACCESS-LIST
<administrative-distance> An IPv6 prefix: address and CIDR mask.
distance (mandatory)

Administrative distance.

distance <uint8>
access-list

Access list name.

access-list ACCESS-LIST
ACCESS-LIST Access list name.
ip-prefix (state only)

IP source prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-unicast administrative-distance <administrative-distance> ip-prefix

route-target

Route target list.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast route-target
redirect-import

Flow-spec redirect type route target, Import routes to this address- family.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast route-target
vrouter running route-target# redirect-import REDIRECT-IMPORT
REDIRECT-IMPORT values Description
<string> Extended communities or route-target attribute.
<string> Extended communities or route-target attribute.
<string> Extended communities or route-target attribute.

maximum-path

Forward packets over multiple paths.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast maximum-path
ebgp

Ebgp number of paths.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast maximum-path
vrouter running maximum-path# ebgp <uint8>
Default value
16
ibgp

Ibgp number of paths.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast maximum-path
vrouter running maximum-path# ibgp <uint8>
Default value
16
equal-cluster-length

If true, match the cluster length.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast maximum-path
vrouter running maximum-path# equal-cluster-length true|false
Default value
false

bgp-distance

Configure BGP distance.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast bgp-distance
external-routes

Distance for routes external to the AS.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast bgp-distance
vrouter running bgp-distance# external-routes <uint8>
Default value
20
internal-routes

Distance for routes internal to the AS.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast bgp-distance
vrouter running bgp-distance# internal-routes <uint8>
Default value
200
local-routes

Distance for local routes.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-unicast bgp-distance
vrouter running bgp-distance# local-routes <uint8>
Default value
200

ipv6-multicast

Configure IPv6 multicast address family.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-multicast

enabled

Enable or disable IPv6 multicast Address Family.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-multicast
vrouter running ipv6-multicast# enabled true|false
Default value
true

rib-count (state only)

Routing information base table count.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-multicast rib-count

neighbor-count (state only)

Number of neighbors for this address family.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-multicast neighbor-count

dynamic-neighbor-count (state only)

Number of dynamic neighbors for this address family.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-multicast dynamic-neighbor-count

network

Specify a network to announce via BGP.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-multicast network <network>
<network> An IPv6 prefix: address and CIDR mask.
route-map

Route-map name.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-multicast network <network>
vrouter running network <network># route-map ROUTE-MAP
ROUTE-MAP Route map name.
label-index

Label index to associate with the prefix.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-multicast network <network>
vrouter running network <network># label-index <uint32>
ip-prefix (state only)

IPv6 prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-multicast network <network> ip-prefix
route (state only)

Route operational state.

validity (state only)

Route validity.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-multicast network <network> route <string> validity
route-type (state only)

Internal or external route.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-multicast network <network> route <string> route-type
prefix (state only)

Route prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-multicast network <network> route <string> prefix
prefix-length (state only)

Route prefix length.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-multicast network <network> route <string> prefix-length
med (state only)

Multi Exit Discriminator.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-multicast network <network> route <string> med
origin (state only)

Route origin.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-multicast network <network> route <string> origin
packet-length (state only)

Packet length.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-multicast network <network> route <string> packet-length
nexthop (state only)

Route nexthop.

used (state only)

Nexthop used.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-multicast network <network> route <string> nexthop <nexthop> used

administrative-distance

Define administrative distance.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-multicast
vrouter running ipv6-multicast# administrative-distance <administrative-distance> \
... distance <uint8> access-list ACCESS-LIST
<administrative-distance> An IPv6 prefix: address and CIDR mask.
distance (mandatory)

Administrative distance.

distance <uint8>
access-list

Access list name.

access-list ACCESS-LIST
ACCESS-LIST Access list name.
ip-prefix (state only)

IP source prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-multicast administrative-distance <administrative-distance> ip-prefix

bgp-distance

Configure BGP distance.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-multicast bgp-distance
external-routes

Distance for routes external to the AS.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-multicast bgp-distance
vrouter running bgp-distance# external-routes <uint8>
Default value
20
internal-routes

Distance for routes internal to the AS.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-multicast bgp-distance
vrouter running bgp-distance# internal-routes <uint8>
Default value
200
local-routes

Distance for local routes.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-multicast bgp-distance
vrouter running bgp-distance# local-routes <uint8>
Default value
200

ipv6-labeled-unicast

Configure IPv6 labeled unicast address family.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-labeled-unicast

enabled

Enable or disable IPv6 labeled unicast Address Family.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# enabled true|false
Default value
true

rib-count (state only)

Routing information base table count.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-labeled-unicast rib-count

neighbor-count (state only)

Number of neighbors for this address family.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-labeled-unicast neighbor-count

dynamic-neighbor-count (state only)

Number of dynamic neighbors for this address family.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-labeled-unicast dynamic-neighbor-count

maximum-path

Forward packets over multiple paths.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-labeled-unicast maximum-path
ebgp

Ebgp number of paths.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-labeled-unicast maximum-path
vrouter running maximum-path# ebgp <uint8>
Default value
16
ibgp

Ibgp number of paths.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-labeled-unicast maximum-path
vrouter running maximum-path# ibgp <uint8>
Default value
16
equal-cluster-length

If true, match the cluster length.

vrouter running config# vrf <vrf> routing bgp address-family ipv6-labeled-unicast maximum-path
vrouter running maximum-path# equal-cluster-length true|false
Default value
false

ipv6-flowspec (state only)

Configure IPv6 Flowspec address family.

rib-count (state only)

Routing information base table count.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-flowspec rib-count

neighbor-count (state only)

Number of neighbors for this address family.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-flowspec neighbor-count

dynamic-neighbor-count (state only)

Number of dynamic neighbors for this address family.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-flowspec dynamic-neighbor-count

route (state only)

Route operational state.

to (state only)

Route destination prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-flowspec route <uint32> to
from (state only)

Route source prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-flowspec route <uint32> from
peer-id (state only)

Route state identifier.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-flowspec route <uint32> peer-id
validity (state only)

Route validity.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-flowspec route <uint32> validity
route-type (state only)

Internal or external route.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-flowspec route <uint32> route-type
prefix (state only)

Route prefix.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-flowspec route <uint32> prefix
prefix-length (state only)

Route prefix length.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-flowspec route <uint32> prefix-length
med (state only)

Multi Exit Discriminator.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-flowspec route <uint32> med
origin (state only)

Route origin.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-flowspec route <uint32> origin
packet-length (state only)

Packet length.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-flowspec route <uint32> packet-length
nexthop (state only)

Route nexthop.

used (state only)

Nexthop used.

vrouter> show state vrf <vrf> routing bgp address-family ipv6-flowspec route <uint32> nexthop <nexthop> used

neighbor-group

List of BGP peer-groups configured on the local system - uniquely identified by peer-group name.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string>

remote-as

Remote AS number.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string>
vrouter running neighbor-group <string># remote-as REMOTE-AS
REMOTE-AS values Description
<uint32> No description.
external External BGP peer.
internal Internal BGP peer.

capability

Advertise capability to the peer.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string>
vrouter running neighbor-group <string># capability CAPABILITY
CAPABILITY values Description
dynamic Advertise dynamic capability to this neighbor.
extended-nexthop Advertise extended nexthop capability to the peer.

capability-negotiate

If true, perform capability negotiation.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string>
vrouter running neighbor-group <string># capability-negotiate true|false
Default value
true

ebgp-multihop

Allow EBGP neighbors not on directly connected networks.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string>
vrouter running neighbor-group <string># ebgp-multihop <uint8>

enforce-first-as

If true, enforce the first AS for EBGP routes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string>
vrouter running neighbor-group <string># enforce-first-as true|false
Default value
false

enforce-multihop

If true, enforce EBGP neighbors perform multihop.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string>
vrouter running neighbor-group <string># enforce-multihop true|false
Default value
false

neighbor-description

Neighbor specific description: up to 80 characters describing this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string>
vrouter running neighbor-group <string># neighbor-description <string>

override-capability

If true, override capability negotiation result.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string>
vrouter running neighbor-group <string># override-capability true|false
Default value
false

passive

If true, don’t send open messages to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string>
vrouter running neighbor-group <string># passive true|false
Default value
false

password

Set a password.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string>
vrouter running neighbor-group <string># password <string>

solo

If true, solo peer - part of its own update group.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string>
vrouter running neighbor-group <string># solo true|false
Default value
false

strict-capability-match

Enable or disable strict capability negotiation match.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string>
vrouter running neighbor-group <string># strict-capability-match true|false
Default value
false

ttl-security-hops

Specify the maximum number of hops to the BGP peer.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string>
vrouter running neighbor-group <string># ttl-security-hops <uint8>

update-source

Source of routing updates.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string>
vrouter running neighbor-group <string># update-source UPDATE-SOURCE
UPDATE-SOURCE values Description
<A.B.C.D> An IPv4 address.
<X:X::X:X> An IPv6 address.
<ifname> An interface name.

name (state only)

Reference to the name of the BGP neighbor-group used as a key in the neighbor-group list.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> name

remote-neighbor-group (state only)

Remote neighbor group.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> remote-neighbor-group

remote-router-id (state only)

Remote router identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> remote-router-id

state (state only)

BGP router status.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> state

min-time-btwn-advertisement (state only)

Minimum time between advertisement runs in miliseconds.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> min-time-btwn-advertisement

last-reset (state only)

Last reset.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> last-reset

bgp-connection (state only)

BGP connection type.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> bgp-connection

connect-retry-timer (state only)

BGP connect retry timer in seconds.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> connect-retry-timer

estimated-rount-trip-time (state only)

Estimated round trip time in miliseconds.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> estimated-rount-trip-time

local-as

Specify a local-as number.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> local-as

as-number (mandatory)

AS number used as local AS.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> local-as
vrouter running local-as# as-number <uint32>

no-prepend

If true, do not prepend local-as to updates from ebgp peers.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> local-as
vrouter running local-as# no-prepend true|false
Default value
false

replace-as

If true, do not prepend local-as to updates from ibgp peers.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> local-as
vrouter running local-as# replace-as true|false
Default value
false

shutdown

Administratively shut down this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> shutdown

message

Shutdown message.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> shutdown
vrouter running shutdown# message <string>

timers

Config parameters related to timers associated with the BGP peer.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> timers

connect-retry

Time interval in seconds between attempts to establish a session with the peer.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> timers
vrouter running timers# connect-retry <uint16>

keepalive-interval

Time interval in seconds between transmission of keepalive messages to the neighbor. Typically set to 1/3 the hold-time.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> timers
vrouter running timers# keepalive-interval <uint16>

hold-time

Time interval in seconds that a BGP session will be considered active in the absence of keepalive or other messages from the peer. The hold- time is typically set to 3x the keepalive-interval.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> timers
vrouter running timers# hold-time <uint16>

address-family

Address-families associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family

ipv4-unicast

IPv4 unicast address-family associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast
enabled

Enable or disable IPv4 unicast Address Family for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast
vrouter running ipv4-unicast# enabled true|false
Default value
true
as-override

If true, disable checking if nexthop is connected on ebgp sessions.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast
vrouter running ipv4-unicast# as-override true|false
Default value
false
send-community

Send Community attribute to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast
vrouter running ipv4-unicast# send-community SEND-COMMUNITY
SEND-COMMUNITY values Description
all Send Standard and Extended Community attributes.
extended Send Extended Community attributes.
standard Send Standard Community attributes.
none Do not send Standard or Extended Community attributes.
Default value
all
weight

Set default weight for routes from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast
vrouter running ipv4-unicast# weight <uint16>
allowas-in

Accept as-path with my AS present in it.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast
vrouter running ipv4-unicast# allowas-in ALLOWAS-IN
ALLOWAS-IN values Description
<uint8> No description.
origin Only accept my AS in the as-path if the route was originated in my AS.
attribute-unchanged

BGP attribute is propagated unchanged to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast
vrouter running ipv4-unicast# attribute-unchanged ATTRIBUTE-UNCHANGED
ATTRIBUTE-UNCHANGED values Description
as-path As-path attribute.
med Med attribute.
nexthop Nexthop attribute.
route-server-client

If true, configure a neighbor as Route Server client.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast
vrouter running ipv4-unicast# route-server-client true|false
Default value
false
soft-reconfiguration-inbound

If true, allow inbound soft reconfiguration for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast
vrouter running ipv4-unicast# soft-reconfiguration-inbound true|false
Default value
false
route-reflector-client

If true, configure a neighbor as Route Reflector client.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast
vrouter running ipv4-unicast# route-reflector-client true|false
Default value
false
capability-orf-prefix-list

Advertise prefixlist ORF capability to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast
vrouter running ipv4-unicast# capability-orf-prefix-list CAPABILITY-ORF-PREFIX-LIST
CAPABILITY-ORF-PREFIX-LIST values Description
both Capability to SEND and RECEIVE the ORF to/from this neighbor.
send Capability to SEND the ORF to this neighbor.
receive Capability to RECEIVE the ORF from this neighbor.
unsuppress-map

Route-map to selectively unsuppress suppressed routes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast
vrouter running ipv4-unicast# unsuppress-map UNSUPPRESS-MAP
UNSUPPRESS-MAP Route map name.
update-group-id (state only)

Update group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast update-group-id
sub-group-id (state only)

Sub-group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast sub-group-id
packet-queue-length (state only)

Packet queue length.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast packet-queue-length
accepted-prefix (state only)

Accepted prefix counter.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast accepted-prefix
addpath

Configure addpath.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast addpath
tx-all-paths

If true, use addpath to advertise all paths to a neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast addpath
vrouter running addpath# tx-all-paths true|false
Default value
false
tx-best-path-per-AS

If true, use addpath to advertise the bestpath per each neighboring AS.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast addpath
vrouter running addpath# tx-best-path-per-AS true|false
Default value
false
distribute-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast
vrouter running ipv4-unicast# distribute-list <distribute-list> access-list ACCESS-LIST
<distribute-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list ACCESS-LIST
ACCESS-LIST Access list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast distribute-list <distribute-list> update-direction
maximum-prefix

Maximum number of prefixes to accept from this peer.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast maximum-prefix
maximum (mandatory)

Maximum number of prefix limit.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast maximum-prefix
vrouter running maximum-prefix# maximum <uint32>
threshold

Threshold value (%) at which to generate a warning msg.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast maximum-prefix
vrouter running maximum-prefix# threshold <uint8>
Default value
75
restart

Restart interval in minutes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast maximum-prefix
vrouter running maximum-prefix# restart <int16>
warning-only

If true, only give warning message when limit is exceeded.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast maximum-prefix
vrouter running maximum-prefix# warning-only true|false
Default value
false
nexthop-self

Disable the next hop calculation for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast nexthop-self
force

If true, set the next hop to self for reflected routes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast nexthop-self
vrouter running nexthop-self# force true|false
Default value
false
as-outbound-update

Remove or replace ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast as-outbound-update
action

Action to apply for ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast as-outbound-update
vrouter running as-outbound-update# action ACTION
ACTION values Description
replace Replace ASNs in outbound updates by our ASN.
remove Remove ASN in outbound updates.
Default value
remove
as-type

Apply to private AS numbers or all.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast as-outbound-update
vrouter running as-outbound-update# as-type AS-TYPE
AS-TYPE values Description
private Apply to private AS numbers only.
all Apply to all AS numbers.
Default value
private
filter-list

Establish BGP filters.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast
vrouter running ipv4-unicast# filter-list <filter-list> access-list <as-path-access-list...
<filter-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list <as-path-access-list>
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast filter-list <filter-list> update-direction
prefix-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast
vrouter running ipv4-unicast# prefix-list <prefix-list> prefix-list-name PREFIX-LIST-NAME
<prefix-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
prefix-list-name (mandatory)

Name of the prefix list.

prefix-list-name PREFIX-LIST-NAME
PREFIX-LIST-NAME Prefix list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast prefix-list <prefix-list> update-direction
route-map

Apply route map to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast
vrouter running ipv4-unicast# route-map <route-map> route-map-name ROUTE-MAP-NAME
<route-map> values Description
in Apply map to incoming routes.
out Apply map to outbound routes.
route-map-name (mandatory)

Route-map name.

route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME Route map name.
route-direction (state only)

Route direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast route-map <route-map> route-direction
default-originate

Originate default route to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast default-originate
route-map

Route-map to specify criteria to originate default.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-unicast default-originate
vrouter running default-originate# route-map ROUTE-MAP
ROUTE-MAP Route map name.

ipv4-multicast

IPv4 multicast address-family associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast
enabled

Enable or disable IPv4 multicast Address Family for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast
vrouter running ipv4-multicast# enabled true|false
Default value
true
as-override

If true, disable checking if nexthop is connected on ebgp sessions.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast
vrouter running ipv4-multicast# as-override true|false
Default value
false
send-community

Send Community attribute to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast
vrouter running ipv4-multicast# send-community SEND-COMMUNITY
SEND-COMMUNITY values Description
all Send Standard and Extended Community attributes.
extended Send Extended Community attributes.
standard Send Standard Community attributes.
none Do not send Standard or Extended Community attributes.
Default value
all
weight

Set default weight for routes from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast
vrouter running ipv4-multicast# weight <uint16>
allowas-in

Accept as-path with my AS present in it.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast
vrouter running ipv4-multicast# allowas-in ALLOWAS-IN
ALLOWAS-IN values Description
<uint8> No description.
origin Only accept my AS in the as-path if the route was originated in my AS.
attribute-unchanged

BGP attribute is propagated unchanged to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast
vrouter running ipv4-multicast# attribute-unchanged ATTRIBUTE-UNCHANGED
ATTRIBUTE-UNCHANGED values Description
as-path As-path attribute.
med Med attribute.
nexthop Nexthop attribute.
route-server-client

If true, configure a neighbor as Route Server client.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast
vrouter running ipv4-multicast# route-server-client true|false
Default value
false
soft-reconfiguration-inbound

If true, allow inbound soft reconfiguration for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast
vrouter running ipv4-multicast# soft-reconfiguration-inbound true|false
Default value
false
route-reflector-client

If true, configure a neighbor as Route Reflector client.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast
vrouter running ipv4-multicast# route-reflector-client true|false
Default value
false
capability-orf-prefix-list

Advertise prefixlist ORF capability to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast
vrouter running ipv4-multicast# capability-orf-prefix-list CAPABILITY-ORF-PREFIX-LIST
CAPABILITY-ORF-PREFIX-LIST values Description
both Capability to SEND and RECEIVE the ORF to/from this neighbor.
send Capability to SEND the ORF to this neighbor.
receive Capability to RECEIVE the ORF from this neighbor.
unsuppress-map

Route-map to selectively unsuppress suppressed routes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast
vrouter running ipv4-multicast# unsuppress-map UNSUPPRESS-MAP
UNSUPPRESS-MAP Route map name.
update-group-id (state only)

Update group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast update-group-id
sub-group-id (state only)

Sub-group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast sub-group-id
packet-queue-length (state only)

Packet queue length.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast packet-queue-length
accepted-prefix (state only)

Accepted prefix counter.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast accepted-prefix
addpath

Configure addpath.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast addpath
tx-all-paths

If true, use addpath to advertise all paths to a neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast addpath
vrouter running addpath# tx-all-paths true|false
Default value
false
tx-best-path-per-AS

If true, use addpath to advertise the bestpath per each neighboring AS.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast addpath
vrouter running addpath# tx-best-path-per-AS true|false
Default value
false
distribute-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast
vrouter running ipv4-multicast# distribute-list <distribute-list> access-list ACCESS-LIST
<distribute-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list ACCESS-LIST
ACCESS-LIST Access list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast distribute-list <distribute-list> update-direction
maximum-prefix

Maximum number of prefixes to accept from this peer.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast maximum-prefix
maximum (mandatory)

Maximum number of prefix limit.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast maximum-prefix
vrouter running maximum-prefix# maximum <uint32>
threshold

Threshold value (%) at which to generate a warning msg.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast maximum-prefix
vrouter running maximum-prefix# threshold <uint8>
Default value
75
restart

Restart interval in minutes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast maximum-prefix
vrouter running maximum-prefix# restart <int16>
warning-only

If true, only give warning message when limit is exceeded.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast maximum-prefix
vrouter running maximum-prefix# warning-only true|false
Default value
false
nexthop-self

Disable the next hop calculation for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast nexthop-self
force

If true, set the next hop to self for reflected routes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast nexthop-self
vrouter running nexthop-self# force true|false
Default value
false
as-outbound-update

Remove or replace ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast as-outbound-update
action

Action to apply for ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast as-outbound-update
vrouter running as-outbound-update# action ACTION
ACTION values Description
replace Replace ASNs in outbound updates by our ASN.
remove Remove ASN in outbound updates.
Default value
remove
as-type

Apply to private AS numbers or all.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast as-outbound-update
vrouter running as-outbound-update# as-type AS-TYPE
AS-TYPE values Description
private Apply to private AS numbers only.
all Apply to all AS numbers.
Default value
private
filter-list

Establish BGP filters.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast
vrouter running ipv4-multicast# filter-list <filter-list> access-list <as-path-access-list...
<filter-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list <as-path-access-list>
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast filter-list <filter-list> update-direction
prefix-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast
vrouter running ipv4-multicast# prefix-list <prefix-list> prefix-list-name PREFIX-LIST-NAME
<prefix-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
prefix-list-name (mandatory)

Name of the prefix list.

prefix-list-name PREFIX-LIST-NAME
PREFIX-LIST-NAME Prefix list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast prefix-list <prefix-list> update-direction
route-map

Apply route map to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast
vrouter running ipv4-multicast# route-map <route-map> route-map-name ROUTE-MAP-NAME
<route-map> values Description
in Apply map to incoming routes.
out Apply map to outbound routes.
route-map-name (mandatory)

Route-map name.

route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME Route map name.
route-direction (state only)

Route direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast route-map <route-map> route-direction
default-originate

Originate default route to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast default-originate
route-map

Route-map to specify criteria to originate default.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-multicast default-originate
vrouter running default-originate# route-map ROUTE-MAP
ROUTE-MAP Route map name.

ipv4-labeled-unicast

IPv4 labeled unicast address-family associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast
enabled

Enable or disable IPv4 labeled unicast Address Family for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# enabled true|false
Default value
true
as-override

If true, disable checking if nexthop is connected on ebgp sessions.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# as-override true|false
Default value
false
send-community

Send Community attribute to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# send-community SEND-COMMUNITY
SEND-COMMUNITY values Description
all Send Standard and Extended Community attributes.
extended Send Extended Community attributes.
standard Send Standard Community attributes.
none Do not send Standard or Extended Community attributes.
Default value
all
weight

Set default weight for routes from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# weight <uint16>
allowas-in

Accept as-path with my AS present in it.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# allowas-in ALLOWAS-IN
ALLOWAS-IN values Description
<uint8> No description.
origin Only accept my AS in the as-path if the route was originated in my AS.
attribute-unchanged

BGP attribute is propagated unchanged to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# attribute-unchanged ATTRIBUTE-UNCHANGED
ATTRIBUTE-UNCHANGED values Description
as-path As-path attribute.
med Med attribute.
nexthop Nexthop attribute.
route-server-client

If true, configure a neighbor as Route Server client.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# route-server-client true|false
Default value
false
soft-reconfiguration-inbound

If true, allow inbound soft reconfiguration for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# soft-reconfiguration-inbound true|false
Default value
false
route-reflector-client

If true, configure a neighbor as Route Reflector client.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# route-reflector-client true|false
Default value
false
capability-orf-prefix-list

Advertise prefixlist ORF capability to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# capability-orf-prefix-list CAPABILITY-ORF-PREFIX-LIST
CAPABILITY-ORF-PREFIX-LIST values Description
both Capability to SEND and RECEIVE the ORF to/from this neighbor.
send Capability to SEND the ORF to this neighbor.
receive Capability to RECEIVE the ORF from this neighbor.
unsuppress-map

Route-map to selectively unsuppress suppressed routes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# unsuppress-map UNSUPPRESS-MAP
UNSUPPRESS-MAP Route map name.
update-group-id (state only)

Update group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast update-group-id
sub-group-id (state only)

Sub-group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast sub-group-id
packet-queue-length (state only)

Packet queue length.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast packet-queue-length
accepted-prefix (state only)

Accepted prefix counter.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast accepted-prefix
addpath

Configure addpath.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast addpath
tx-all-paths

If true, use addpath to advertise all paths to a neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast addpath
vrouter running addpath# tx-all-paths true|false
Default value
false
tx-best-path-per-AS

If true, use addpath to advertise the bestpath per each neighboring AS.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast addpath
vrouter running addpath# tx-best-path-per-AS true|false
Default value
false
distribute-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# distribute-list <distribute-list> access-list ACCESS-LIST
<distribute-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list ACCESS-LIST
ACCESS-LIST Access list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast distribute-list <distribute-list> update-direction
maximum-prefix

Maximum number of prefixes to accept from this peer.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast maximum-prefix
maximum (mandatory)

Maximum number of prefix limit.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast maximum-prefix
vrouter running maximum-prefix# maximum <uint32>
threshold

Threshold value (%) at which to generate a warning msg.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast maximum-prefix
vrouter running maximum-prefix# threshold <uint8>
Default value
75
restart

Restart interval in minutes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast maximum-prefix
vrouter running maximum-prefix# restart <int16>
warning-only

If true, only give warning message when limit is exceeded.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast maximum-prefix
vrouter running maximum-prefix# warning-only true|false
Default value
false
nexthop-self

Disable the next hop calculation for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast nexthop-self
force

If true, set the next hop to self for reflected routes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast nexthop-self
vrouter running nexthop-self# force true|false
Default value
false
as-outbound-update

Remove or replace ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast as-outbound-update
action

Action to apply for ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast as-outbound-update
vrouter running as-outbound-update# action ACTION
ACTION values Description
replace Replace ASNs in outbound updates by our ASN.
remove Remove ASN in outbound updates.
Default value
remove
as-type

Apply to private AS numbers or all.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast as-outbound-update
vrouter running as-outbound-update# as-type AS-TYPE
AS-TYPE values Description
private Apply to private AS numbers only.
all Apply to all AS numbers.
Default value
private
filter-list

Establish BGP filters.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# filter-list <filter-list> access-list <as-path-access-list...
<filter-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list <as-path-access-list>
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast filter-list <filter-list> update-direction
prefix-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# prefix-list <prefix-list> prefix-list-name PREFIX-LIST-NAME
<prefix-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
prefix-list-name (mandatory)

Name of the prefix list.

prefix-list-name PREFIX-LIST-NAME
PREFIX-LIST-NAME Prefix list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast prefix-list <prefix-list> update-direction
route-map

Apply route map to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# route-map <route-map> route-map-name ROUTE-MAP-NAME
<route-map> values Description
in Apply map to incoming routes.
out Apply map to outbound routes.
route-map-name (mandatory)

Route-map name.

route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME Route map name.
route-direction (state only)

Route direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast route-map <route-map> route-direction
default-originate

Originate default route to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast default-originate
route-map

Route-map to specify criteria to originate default.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-labeled-unicast default-originate
vrouter running default-originate# route-map ROUTE-MAP
ROUTE-MAP Route map name.

ipv4-flowspec

IPv4 Flowspec address-family associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-flowspec
enabled

Enable or disable IPv4 Flowspec Address Family for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-flowspec
vrouter running ipv4-flowspec# enabled true|false
Default value
true
route-server-client

If true, configure a neighbor as Route Server client.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-flowspec
vrouter running ipv4-flowspec# route-server-client true|false
Default value
false
soft-reconfiguration-inbound

If true, allow inbound soft reconfiguration for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-flowspec
vrouter running ipv4-flowspec# soft-reconfiguration-inbound true|false
Default value
false
route-reflector-client

If true, configure a neighbor as Route Reflector client.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-flowspec
vrouter running ipv4-flowspec# route-reflector-client true|false
Default value
false
update-group-id (state only)

Update group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-flowspec update-group-id
sub-group-id (state only)

Sub-group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-flowspec sub-group-id
packet-queue-length (state only)

Packet queue length.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-flowspec packet-queue-length
accepted-prefix (state only)

Accepted prefix counter.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-flowspec accepted-prefix
filter-list

Establish BGP filters.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-flowspec
vrouter running ipv4-flowspec# filter-list <filter-list> access-list <as-path-access-list...
<filter-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list <as-path-access-list>
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-flowspec filter-list <filter-list> update-direction
prefix-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-flowspec
vrouter running ipv4-flowspec# prefix-list <prefix-list> prefix-list-name PREFIX-LIST-NAME
<prefix-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
prefix-list-name (mandatory)

Name of the prefix list.

prefix-list-name PREFIX-LIST-NAME
PREFIX-LIST-NAME Prefix list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-flowspec prefix-list <prefix-list> update-direction
route-map

Apply route map to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-flowspec
vrouter running ipv4-flowspec# route-map <route-map> route-map-name ROUTE-MAP-NAME
<route-map> values Description
in Apply map to incoming routes.
out Apply map to outbound routes.
route-map-name (mandatory)

Route-map name.

route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME Route map name.
route-direction (state only)

Route direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv4-flowspec route-map <route-map> route-direction

ipv6-unicast

IPv6 unicast address-family associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
enabled

Enable or disable IPv6 unicast Address Family for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
vrouter running ipv6-unicast# enabled true|false
Default value
true
nexthop-local-unchanged

If true, leave link-local nexthop unchanged for this peer.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
vrouter running ipv6-unicast# nexthop-local-unchanged true|false
Default value
false
as-override

If true, disable checking if nexthop is connected on ebgp sessions.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
vrouter running ipv6-unicast# as-override true|false
Default value
false
send-community

Send Community attribute to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
vrouter running ipv6-unicast# send-community SEND-COMMUNITY
SEND-COMMUNITY values Description
all Send Standard and Extended Community attributes.
extended Send Extended Community attributes.
standard Send Standard Community attributes.
none Do not send Standard or Extended Community attributes.
Default value
all
weight

Set default weight for routes from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
vrouter running ipv6-unicast# weight <uint16>
allowas-in

Accept as-path with my AS present in it.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
vrouter running ipv6-unicast# allowas-in ALLOWAS-IN
ALLOWAS-IN values Description
<uint8> No description.
origin Only accept my AS in the as-path if the route was originated in my AS.
attribute-unchanged

BGP attribute is propagated unchanged to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
vrouter running ipv6-unicast# attribute-unchanged ATTRIBUTE-UNCHANGED
ATTRIBUTE-UNCHANGED values Description
as-path As-path attribute.
med Med attribute.
nexthop Nexthop attribute.
route-server-client

If true, configure a neighbor as Route Server client.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
vrouter running ipv6-unicast# route-server-client true|false
Default value
false
soft-reconfiguration-inbound

If true, allow inbound soft reconfiguration for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
vrouter running ipv6-unicast# soft-reconfiguration-inbound true|false
Default value
false
route-reflector-client

If true, configure a neighbor as Route Reflector client.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
vrouter running ipv6-unicast# route-reflector-client true|false
Default value
false
capability-orf-prefix-list

Advertise prefixlist ORF capability to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
vrouter running ipv6-unicast# capability-orf-prefix-list CAPABILITY-ORF-PREFIX-LIST
CAPABILITY-ORF-PREFIX-LIST values Description
both Capability to SEND and RECEIVE the ORF to/from this neighbor.
send Capability to SEND the ORF to this neighbor.
receive Capability to RECEIVE the ORF from this neighbor.
unsuppress-map

Route-map to selectively unsuppress suppressed routes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
vrouter running ipv6-unicast# unsuppress-map UNSUPPRESS-MAP
UNSUPPRESS-MAP Route map name.
update-group-id (state only)

Update group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast update-group-id
sub-group-id (state only)

Sub-group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast sub-group-id
packet-queue-length (state only)

Packet queue length.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast packet-queue-length
accepted-prefix (state only)

Accepted prefix counter.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast accepted-prefix
addpath

Configure addpath.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast addpath
tx-all-paths

If true, use addpath to advertise all paths to a neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast addpath
vrouter running addpath# tx-all-paths true|false
Default value
false
tx-best-path-per-AS

If true, use addpath to advertise the bestpath per each neighboring AS.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast addpath
vrouter running addpath# tx-best-path-per-AS true|false
Default value
false
distribute-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
vrouter running ipv6-unicast# distribute-list <distribute-list> access-list ACCESS-LIST
<distribute-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list ACCESS-LIST
ACCESS-LIST Access list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast distribute-list <distribute-list> update-direction
maximum-prefix

Maximum number of prefixes to accept from this peer.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast maximum-prefix
maximum (mandatory)

Maximum number of prefix limit.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast maximum-prefix
vrouter running maximum-prefix# maximum <uint32>
threshold

Threshold value (%) at which to generate a warning msg.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast maximum-prefix
vrouter running maximum-prefix# threshold <uint8>
Default value
75
restart

Restart interval in minutes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast maximum-prefix
vrouter running maximum-prefix# restart <int16>
warning-only

If true, only give warning message when limit is exceeded.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast maximum-prefix
vrouter running maximum-prefix# warning-only true|false
Default value
false
nexthop-self

Disable the next hop calculation for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast nexthop-self
force

If true, set the next hop to self for reflected routes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast nexthop-self
vrouter running nexthop-self# force true|false
Default value
false
as-outbound-update

Remove or replace ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast as-outbound-update
action

Action to apply for ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast as-outbound-update
vrouter running as-outbound-update# action ACTION
ACTION values Description
replace Replace ASNs in outbound updates by our ASN.
remove Remove ASN in outbound updates.
Default value
remove
as-type

Apply to private AS numbers or all.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast as-outbound-update
vrouter running as-outbound-update# as-type AS-TYPE
AS-TYPE values Description
private Apply to private AS numbers only.
all Apply to all AS numbers.
Default value
private
filter-list

Establish BGP filters.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
vrouter running ipv6-unicast# filter-list <filter-list> access-list <as-path-access-list...
<filter-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list <as-path-access-list>
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast filter-list <filter-list> update-direction
prefix-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
vrouter running ipv6-unicast# prefix-list <prefix-list> prefix-list-name PREFIX-LIST-NAME
<prefix-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
prefix-list-name (mandatory)

Name of the prefix list.

prefix-list-name PREFIX-LIST-NAME
PREFIX-LIST-NAME Prefix list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast prefix-list <prefix-list> update-direction
route-map

Apply route map to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast
vrouter running ipv6-unicast# route-map <route-map> route-map-name ROUTE-MAP-NAME
<route-map> values Description
in Apply map to incoming routes.
out Apply map to outbound routes.
route-map-name (mandatory)

Route-map name.

route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME Route map name.
route-direction (state only)

Route direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast route-map <route-map> route-direction
default-originate

Originate default route to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast default-originate
route-map

Route-map to specify criteria to originate default.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-unicast default-originate
vrouter running default-originate# route-map ROUTE-MAP
ROUTE-MAP Route map name.

ipv6-multicast

IPv6 multicast address-family associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast
enabled

Enable or disable IPv6 multicast Address Family for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast
vrouter running ipv6-multicast# enabled true|false
Default value
true
as-override

If true, disable checking if nexthop is connected on ebgp sessions.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast
vrouter running ipv6-multicast# as-override true|false
Default value
false
send-community

Send Community attribute to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast
vrouter running ipv6-multicast# send-community SEND-COMMUNITY
SEND-COMMUNITY values Description
all Send Standard and Extended Community attributes.
extended Send Extended Community attributes.
standard Send Standard Community attributes.
none Do not send Standard or Extended Community attributes.
Default value
all
weight

Set default weight for routes from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast
vrouter running ipv6-multicast# weight <uint16>
allowas-in

Accept as-path with my AS present in it.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast
vrouter running ipv6-multicast# allowas-in ALLOWAS-IN
ALLOWAS-IN values Description
<uint8> No description.
origin Only accept my AS in the as-path if the route was originated in my AS.
attribute-unchanged

BGP attribute is propagated unchanged to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast
vrouter running ipv6-multicast# attribute-unchanged ATTRIBUTE-UNCHANGED
ATTRIBUTE-UNCHANGED values Description
as-path As-path attribute.
med Med attribute.
nexthop Nexthop attribute.
route-server-client

If true, configure a neighbor as Route Server client.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast
vrouter running ipv6-multicast# route-server-client true|false
Default value
false
soft-reconfiguration-inbound

If true, allow inbound soft reconfiguration for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast
vrouter running ipv6-multicast# soft-reconfiguration-inbound true|false
Default value
false
route-reflector-client

If true, configure a neighbor as Route Reflector client.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast
vrouter running ipv6-multicast# route-reflector-client true|false
Default value
false
capability-orf-prefix-list

Advertise prefixlist ORF capability to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast
vrouter running ipv6-multicast# capability-orf-prefix-list CAPABILITY-ORF-PREFIX-LIST
CAPABILITY-ORF-PREFIX-LIST values Description
both Capability to SEND and RECEIVE the ORF to/from this neighbor.
send Capability to SEND the ORF to this neighbor.
receive Capability to RECEIVE the ORF from this neighbor.
unsuppress-map

Route-map to selectively unsuppress suppressed routes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast
vrouter running ipv6-multicast# unsuppress-map UNSUPPRESS-MAP
UNSUPPRESS-MAP Route map name.
update-group-id (state only)

Update group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast update-group-id
sub-group-id (state only)

Sub-group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast sub-group-id
packet-queue-length (state only)

Packet queue length.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast packet-queue-length
accepted-prefix (state only)

Accepted prefix counter.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast accepted-prefix
addpath

Configure addpath.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast addpath
tx-all-paths

If true, use addpath to advertise all paths to a neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast addpath
vrouter running addpath# tx-all-paths true|false
Default value
false
tx-best-path-per-AS

If true, use addpath to advertise the bestpath per each neighboring AS.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast addpath
vrouter running addpath# tx-best-path-per-AS true|false
Default value
false
distribute-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast
vrouter running ipv6-multicast# distribute-list <distribute-list> access-list ACCESS-LIST
<distribute-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list ACCESS-LIST
ACCESS-LIST Access list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast distribute-list <distribute-list> update-direction
maximum-prefix

Maximum number of prefixes to accept from this peer.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast maximum-prefix
maximum (mandatory)

Maximum number of prefix limit.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast maximum-prefix
vrouter running maximum-prefix# maximum <uint32>
threshold

Threshold value (%) at which to generate a warning msg.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast maximum-prefix
vrouter running maximum-prefix# threshold <uint8>
Default value
75
restart

Restart interval in minutes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast maximum-prefix
vrouter running maximum-prefix# restart <int16>
warning-only

If true, only give warning message when limit is exceeded.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast maximum-prefix
vrouter running maximum-prefix# warning-only true|false
Default value
false
nexthop-self

Disable the next hop calculation for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast nexthop-self
force

If true, set the next hop to self for reflected routes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast nexthop-self
vrouter running nexthop-self# force true|false
Default value
false
as-outbound-update

Remove or replace ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast as-outbound-update
action

Action to apply for ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast as-outbound-update
vrouter running as-outbound-update# action ACTION
ACTION values Description
replace Replace ASNs in outbound updates by our ASN.
remove Remove ASN in outbound updates.
Default value
remove
as-type

Apply to private AS numbers or all.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast as-outbound-update
vrouter running as-outbound-update# as-type AS-TYPE
AS-TYPE values Description
private Apply to private AS numbers only.
all Apply to all AS numbers.
Default value
private
filter-list

Establish BGP filters.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast
vrouter running ipv6-multicast# filter-list <filter-list> access-list <as-path-access-list...
<filter-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list <as-path-access-list>
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast filter-list <filter-list> update-direction
prefix-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast
vrouter running ipv6-multicast# prefix-list <prefix-list> prefix-list-name PREFIX-LIST-NAME
<prefix-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
prefix-list-name (mandatory)

Name of the prefix list.

prefix-list-name PREFIX-LIST-NAME
PREFIX-LIST-NAME Prefix list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast prefix-list <prefix-list> update-direction
route-map

Apply route map to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast
vrouter running ipv6-multicast# route-map <route-map> route-map-name ROUTE-MAP-NAME
<route-map> values Description
in Apply map to incoming routes.
out Apply map to outbound routes.
route-map-name (mandatory)

Route-map name.

route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME Route map name.
route-direction (state only)

Route direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast route-map <route-map> route-direction
default-originate

Originate default route to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast default-originate
route-map

Route-map to specify criteria to originate default.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-multicast default-originate
vrouter running default-originate# route-map ROUTE-MAP
ROUTE-MAP Route map name.

ipv6-labeled-unicast

IPv6 labeled unicast address-family associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast
enabled

Enable or disable IPv6 labeled unicast Address Family for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# enabled true|false
Default value
true
as-override

If true, disable checking if nexthop is connected on ebgp sessions.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# as-override true|false
Default value
false
send-community

Send Community attribute to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# send-community SEND-COMMUNITY
SEND-COMMUNITY values Description
all Send Standard and Extended Community attributes.
extended Send Extended Community attributes.
standard Send Standard Community attributes.
none Do not send Standard or Extended Community attributes.
Default value
all
weight

Set default weight for routes from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# weight <uint16>
allowas-in

Accept as-path with my AS present in it.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# allowas-in ALLOWAS-IN
ALLOWAS-IN values Description
<uint8> No description.
origin Only accept my AS in the as-path if the route was originated in my AS.
attribute-unchanged

BGP attribute is propagated unchanged to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# attribute-unchanged ATTRIBUTE-UNCHANGED
ATTRIBUTE-UNCHANGED values Description
as-path As-path attribute.
med Med attribute.
nexthop Nexthop attribute.
route-server-client

If true, configure a neighbor as Route Server client.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# route-server-client true|false
Default value
false
soft-reconfiguration-inbound

If true, allow inbound soft reconfiguration for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# soft-reconfiguration-inbound true|false
Default value
false
route-reflector-client

If true, configure a neighbor as Route Reflector client.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# route-reflector-client true|false
Default value
false
capability-orf-prefix-list

Advertise prefixlist ORF capability to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# capability-orf-prefix-list CAPABILITY-ORF-PREFIX-LIST
CAPABILITY-ORF-PREFIX-LIST values Description
both Capability to SEND and RECEIVE the ORF to/from this neighbor.
send Capability to SEND the ORF to this neighbor.
receive Capability to RECEIVE the ORF from this neighbor.
unsuppress-map

Route-map to selectively unsuppress suppressed routes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# unsuppress-map UNSUPPRESS-MAP
UNSUPPRESS-MAP Route map name.
update-group-id (state only)

Update group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast update-group-id
sub-group-id (state only)

Sub-group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast sub-group-id
packet-queue-length (state only)

Packet queue length.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast packet-queue-length
accepted-prefix (state only)

Accepted prefix counter.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast accepted-prefix
addpath

Configure addpath.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast addpath
tx-all-paths

If true, use addpath to advertise all paths to a neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast addpath
vrouter running addpath# tx-all-paths true|false
Default value
false
tx-best-path-per-AS

If true, use addpath to advertise the bestpath per each neighboring AS.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast addpath
vrouter running addpath# tx-best-path-per-AS true|false
Default value
false
distribute-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# distribute-list <distribute-list> access-list ACCESS-LIST
<distribute-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list ACCESS-LIST
ACCESS-LIST Access list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast distribute-list <distribute-list> update-direction
maximum-prefix

Maximum number of prefixes to accept from this peer.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast maximum-prefix
maximum (mandatory)

Maximum number of prefix limit.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast maximum-prefix
vrouter running maximum-prefix# maximum <uint32>
threshold

Threshold value (%) at which to generate a warning msg.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast maximum-prefix
vrouter running maximum-prefix# threshold <uint8>
Default value
75
restart

Restart interval in minutes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast maximum-prefix
vrouter running maximum-prefix# restart <int16>
warning-only

If true, only give warning message when limit is exceeded.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast maximum-prefix
vrouter running maximum-prefix# warning-only true|false
Default value
false
nexthop-self

Disable the next hop calculation for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast nexthop-self
force

If true, set the next hop to self for reflected routes.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast nexthop-self
vrouter running nexthop-self# force true|false
Default value
false
as-outbound-update

Remove or replace ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast as-outbound-update
action

Action to apply for ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast as-outbound-update
vrouter running as-outbound-update# action ACTION
ACTION values Description
replace Replace ASNs in outbound updates by our ASN.
remove Remove ASN in outbound updates.
Default value
remove
as-type

Apply to private AS numbers or all.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast as-outbound-update
vrouter running as-outbound-update# as-type AS-TYPE
AS-TYPE values Description
private Apply to private AS numbers only.
all Apply to all AS numbers.
Default value
private
filter-list

Establish BGP filters.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# filter-list <filter-list> access-list <as-path-access-list...
<filter-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list <as-path-access-list>
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast filter-list <filter-list> update-direction
prefix-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# prefix-list <prefix-list> prefix-list-name PREFIX-LIST-NAME
<prefix-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
prefix-list-name (mandatory)

Name of the prefix list.

prefix-list-name PREFIX-LIST-NAME
PREFIX-LIST-NAME Prefix list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast prefix-list <prefix-list> update-direction
route-map

Apply route map to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# route-map <route-map> route-map-name ROUTE-MAP-NAME
<route-map> values Description
in Apply map to incoming routes.
out Apply map to outbound routes.
route-map-name (mandatory)

Route-map name.

route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME Route map name.
route-direction (state only)

Route direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast route-map <route-map> route-direction
default-originate

Originate default route to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast default-originate
route-map

Route-map to specify criteria to originate default.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-labeled-unicast default-originate
vrouter running default-originate# route-map ROUTE-MAP
ROUTE-MAP Route map name.

ipv6-flowspec

IPv6 Flowspec address-family associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-flowspec
enabled

Enable or disable IPv6 Flowspec Address Family for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-flowspec
vrouter running ipv6-flowspec# enabled true|false
Default value
true
route-server-client

If true, configure a neighbor as Route Server client.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-flowspec
vrouter running ipv6-flowspec# route-server-client true|false
Default value
false
soft-reconfiguration-inbound

If true, allow inbound soft reconfiguration for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-flowspec
vrouter running ipv6-flowspec# soft-reconfiguration-inbound true|false
Default value
false
route-reflector-client

If true, configure a neighbor as Route Reflector client.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-flowspec
vrouter running ipv6-flowspec# route-reflector-client true|false
Default value
false
update-group-id (state only)

Update group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-flowspec update-group-id
sub-group-id (state only)

Sub-group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-flowspec sub-group-id
packet-queue-length (state only)

Packet queue length.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-flowspec packet-queue-length
accepted-prefix (state only)

Accepted prefix counter.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-flowspec accepted-prefix
filter-list

Establish BGP filters.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-flowspec
vrouter running ipv6-flowspec# filter-list <filter-list> access-list <as-path-access-list...
<filter-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list <as-path-access-list>
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-flowspec filter-list <filter-list> update-direction
prefix-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-flowspec
vrouter running ipv6-flowspec# prefix-list <prefix-list> prefix-list-name PREFIX-LIST-NAME
<prefix-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
prefix-list-name (mandatory)

Name of the prefix list.

prefix-list-name PREFIX-LIST-NAME
PREFIX-LIST-NAME Prefix list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-flowspec prefix-list <prefix-list> update-direction
route-map

Apply route map to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-flowspec
vrouter running ipv6-flowspec# route-map <route-map> route-map-name ROUTE-MAP-NAME
<route-map> values Description
in Apply map to incoming routes.
out Apply map to outbound routes.
route-map-name (mandatory)

Route-map name.

route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME Route map name.
route-direction (state only)

Route direction.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> address-family ipv6-flowspec route-map <route-map> route-direction

connections (state only)

Established/dropped connections statistics.

established (state only)

Number of established connections.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> connections established

dropped (state only)

Number of dropped connections.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> connections dropped

local-host (state only)

Local host data.

name (state only)

Local host name.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> local-host name

port (state only)

Local host port.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> local-host port

remote-host (state only)

Remote host data.

name (state only)

Remote host name.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> remote-host name

port (state only)

Remote host port.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> remote-host port

nexthop (state only)

Nexthop data.

address (state only)

Nexthop IP address.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> nexthop address

global-address (state only)

Nexthop global IP address.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> nexthop global-address

local-address (state only)

Nexthop local IP address.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> nexthop local-address

thread (state only)

Read/Write thread.

read-enabled (state only)

Read thread status.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> thread read-enabled

write-enabled (state only)

Write thread status.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> thread write-enabled

message-statistics (state only)

Neighbor messages statistics.

packet-wait-process (state only)

Number of packets waiting to be processed.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> message-statistics packet-wait-process

packet-wait-written (state only)

Number of packets waiting to be written.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> message-statistics packet-wait-written

open-sent (state only)

BGP open messages sent.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> message-statistics open-sent

opens-received (state only)

BGP open messages received.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> message-statistics opens-received

notifications-sent (state only)

Notifications messages sent.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> message-statistics notifications-sent

notifications-received (state only)

Notification messages received.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> message-statistics notifications-received

updates-sent (state only)

Update messages sent.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> message-statistics updates-sent

updates-received (state only)

Update messages received.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> message-statistics updates-received

keepalives-sent (state only)

Keepalive messages sent.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> message-statistics keepalives-sent

keepalives-received (state only)

Keepalive messages received.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> message-statistics keepalives-received

route-refresh-sent (state only)

Route refresh messages sent.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> message-statistics route-refresh-sent

route-refresh-received (state only)

Route refresh messages received.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> message-statistics route-refresh-received

capability-sent (state only)

Capability messages sent.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> message-statistics capability-sent

capability-received (state only)

Capability messages received.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> message-statistics capability-received

total-sent (state only)

Total messages sent.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> message-statistics total-sent

total-received (state only)

Total messages received.

vrouter> show state vrf <vrf> routing bgp neighbor-group <string> message-statistics total-received

neighbor

List of BGP neighbors configured on the local system, uniquely identified by peer IPv[46] address.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
<neighbor> values Description
<A.B.C.D> An IPv4 address.
<X:X::X:X> An IPv6 address.

neighbor-group

Peer group name.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># neighbor-group <neighbor-group>

interface

Name of the interface.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># interface INTERFACE
INTERFACE An interface name.

port

TCP port number.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># port PORT
PORT A 16-bit port number used by a transport protocol such as TCP or UDP.

remote-as

Remote AS number.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># remote-as REMOTE-AS
REMOTE-AS values Description
<uint32> No description.
external External BGP peer.
internal Internal BGP peer.

capability

Advertise capability to the peer.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># capability CAPABILITY
CAPABILITY values Description
dynamic Advertise dynamic capability to this neighbor.
extended-nexthop Advertise extended nexthop capability to the peer.

capability-negotiate

If true, perform capability negotiation.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># capability-negotiate true|false
Default value
true

ebgp-multihop

Allow EBGP neighbors not on directly connected networks.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># ebgp-multihop <uint8>

enforce-first-as

If true, enforce the first AS for EBGP routes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># enforce-first-as true|false
Default value
false

enforce-multihop

If true, enforce EBGP neighbors perform multihop.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># enforce-multihop true|false
Default value
false

neighbor-description

Neighbor specific description: up to 80 characters describing this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># neighbor-description <string>

override-capability

If true, override capability negotiation result.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># override-capability true|false
Default value
false

passive

If true, don’t send open messages to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># passive true|false
Default value
false

password

Set a password.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># password <string>

solo

If true, solo peer - part of its own update group.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># solo true|false
Default value
false

strict-capability-match

Enable or disable strict capability negotiation match.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># strict-capability-match true|false
Default value
false

ttl-security-hops

Specify the maximum number of hops to the BGP peer.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># ttl-security-hops <uint8>

update-source

Source of routing updates.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor>
vrouter running neighbor <neighbor># update-source UPDATE-SOURCE
UPDATE-SOURCE values Description
<A.B.C.D> An IPv4 address.
<X:X::X:X> An IPv6 address.
<ifname> An interface name.

neighbor-address (state only)

IPv4 or IPv6 address of the BGP neighbor.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> neighbor-address

remote-neighbor-group (state only)

Remote neighbor group.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> remote-neighbor-group

remote-router-id (state only)

Remote router identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> remote-router-id

state (state only)

BGP router status.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> state

min-time-btwn-advertisement (state only)

Minimum time between advertisement runs in miliseconds.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> min-time-btwn-advertisement

last-reset (state only)

Last reset.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> last-reset

bgp-connection (state only)

BGP connection type.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> bgp-connection

connect-retry-timer (state only)

BGP connect retry timer in seconds.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> connect-retry-timer

estimated-rount-trip-time (state only)

Estimated round trip time in miliseconds.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> estimated-rount-trip-time

local-as

Specify a local-as number.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> local-as

as-number (mandatory)

AS number used as local AS.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> local-as
vrouter running local-as# as-number <uint32>

no-prepend

If true, do not prepend local-as to updates from ebgp peers.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> local-as
vrouter running local-as# no-prepend true|false
Default value
false

replace-as

If true, do not prepend local-as to updates from ibgp peers.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> local-as
vrouter running local-as# replace-as true|false
Default value
false

shutdown

Administratively shut down this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> shutdown

message

Shutdown message.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> shutdown
vrouter running shutdown# message <string>

timers

Config parameters related to timers associated with the BGP peer.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> timers

advertisement-interval

Minimum time which must elapse between subsequent UPDATE messages relating to a common set of NLRI being transmitted to a peer. This timer is referred to as MinRouteAdvertisementIntervalTimer by RFC 4721 and serves to reduce the number of UPDATE messages transmitted when a particular set of NLRI exhibit instability.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> timers
vrouter running timers# advertisement-interval <uint16>

connect-retry

Time interval in seconds between attempts to establish a session with the peer.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> timers
vrouter running timers# connect-retry <uint16>

keepalive-interval

Time interval in seconds between transmission of keepalive messages to the neighbor. Typically set to 1/3 the hold-time.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> timers
vrouter running timers# keepalive-interval <uint16>

hold-time

Time interval in seconds that a BGP session will be considered active in the absence of keepalive or other messages from the peer. The hold- time is typically set to 3x the keepalive-interval.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> timers
vrouter running timers# hold-time <uint16>

address-family

Address-families associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family

ipv4-unicast

IPv4 unicast address-family associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast
enabled

Enable or disable IPv4 unicast Address Family for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast
vrouter running ipv4-unicast# enabled true|false
Default value
true
as-override

If true, disable checking if nexthop is connected on ebgp sessions.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast
vrouter running ipv4-unicast# as-override true|false
Default value
false
send-community

Send Community attribute to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast
vrouter running ipv4-unicast# send-community SEND-COMMUNITY
SEND-COMMUNITY values Description
all Send Standard and Extended Community attributes.
extended Send Extended Community attributes.
standard Send Standard Community attributes.
none Do not send Standard or Extended Community attributes.
Default value
all
weight

Set default weight for routes from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast
vrouter running ipv4-unicast# weight <uint16>
allowas-in

Accept as-path with my AS present in it.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast
vrouter running ipv4-unicast# allowas-in ALLOWAS-IN
ALLOWAS-IN values Description
<uint8> No description.
origin Only accept my AS in the as-path if the route was originated in my AS.
attribute-unchanged

BGP attribute is propagated unchanged to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast
vrouter running ipv4-unicast# attribute-unchanged ATTRIBUTE-UNCHANGED
ATTRIBUTE-UNCHANGED values Description
as-path As-path attribute.
med Med attribute.
nexthop Nexthop attribute.
route-server-client

If true, configure a neighbor as Route Server client.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast
vrouter running ipv4-unicast# route-server-client true|false
Default value
false
soft-reconfiguration-inbound

If true, allow inbound soft reconfiguration for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast
vrouter running ipv4-unicast# soft-reconfiguration-inbound true|false
Default value
false
route-reflector-client

If true, configure a neighbor as Route Reflector client.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast
vrouter running ipv4-unicast# route-reflector-client true|false
Default value
false
capability-orf-prefix-list

Advertise prefixlist ORF capability to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast
vrouter running ipv4-unicast# capability-orf-prefix-list CAPABILITY-ORF-PREFIX-LIST
CAPABILITY-ORF-PREFIX-LIST values Description
both Capability to SEND and RECEIVE the ORF to/from this neighbor.
send Capability to SEND the ORF to this neighbor.
receive Capability to RECEIVE the ORF from this neighbor.
unsuppress-map

Route-map to selectively unsuppress suppressed routes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast
vrouter running ipv4-unicast# unsuppress-map UNSUPPRESS-MAP
UNSUPPRESS-MAP Route map name.
update-group-id (state only)

Update group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast update-group-id
sub-group-id (state only)

Sub-group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast sub-group-id
packet-queue-length (state only)

Packet queue length.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast packet-queue-length
accepted-prefix (state only)

Accepted prefix counter.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast accepted-prefix
addpath

Configure addpath.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast addpath
tx-all-paths

If true, use addpath to advertise all paths to a neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast addpath
vrouter running addpath# tx-all-paths true|false
Default value
false
tx-best-path-per-AS

If true, use addpath to advertise the bestpath per each neighboring AS.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast addpath
vrouter running addpath# tx-best-path-per-AS true|false
Default value
false
distribute-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast
vrouter running ipv4-unicast# distribute-list <distribute-list> access-list ACCESS-LIST
<distribute-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list ACCESS-LIST
ACCESS-LIST Access list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast distribute-list <distribute-list> update-direction
maximum-prefix

Maximum number of prefixes to accept from this peer.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast maximum-prefix
maximum (mandatory)

Maximum number of prefix limit.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast maximum-prefix
vrouter running maximum-prefix# maximum <uint32>
threshold

Threshold value (%) at which to generate a warning msg.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast maximum-prefix
vrouter running maximum-prefix# threshold <uint8>
Default value
75
restart

Restart interval in minutes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast maximum-prefix
vrouter running maximum-prefix# restart <int16>
warning-only

If true, only give warning message when limit is exceeded.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast maximum-prefix
vrouter running maximum-prefix# warning-only true|false
Default value
false
nexthop-self

Disable the next hop calculation for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast nexthop-self
force

If true, set the next hop to self for reflected routes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast nexthop-self
vrouter running nexthop-self# force true|false
Default value
false
as-outbound-update

Remove or replace ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast as-outbound-update
action

Action to apply for ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast as-outbound-update
vrouter running as-outbound-update# action ACTION
ACTION values Description
replace Replace ASNs in outbound updates by our ASN.
remove Remove ASN in outbound updates.
Default value
remove
as-type

Apply to private AS numbers or all.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast as-outbound-update
vrouter running as-outbound-update# as-type AS-TYPE
AS-TYPE values Description
private Apply to private AS numbers only.
all Apply to all AS numbers.
Default value
private
filter-list

Establish BGP filters.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast
vrouter running ipv4-unicast# filter-list <filter-list> access-list <as-path-access-list...
<filter-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list <as-path-access-list>
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast filter-list <filter-list> update-direction
prefix-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast
vrouter running ipv4-unicast# prefix-list <prefix-list> prefix-list-name PREFIX-LIST-NAME
<prefix-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
prefix-list-name (mandatory)

Name of the prefix list.

prefix-list-name PREFIX-LIST-NAME
PREFIX-LIST-NAME Prefix list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast prefix-list <prefix-list> update-direction
route-map

Apply route map to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast
vrouter running ipv4-unicast# route-map <route-map> route-map-name ROUTE-MAP-NAME
<route-map> values Description
in Apply map to incoming routes.
out Apply map to outbound routes.
route-map-name (mandatory)

Route-map name.

route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME Route map name.
route-direction (state only)

Route direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast route-map <route-map> route-direction
default-originate

Originate default route to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast default-originate
route-map

Route-map to specify criteria to originate default.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-unicast default-originate
vrouter running default-originate# route-map ROUTE-MAP
ROUTE-MAP Route map name.

ipv4-multicast

IPv4 multicast address-family associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast
enabled

Enable or disable IPv4 multicast Address Family for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast
vrouter running ipv4-multicast# enabled true|false
Default value
true
as-override

If true, disable checking if nexthop is connected on ebgp sessions.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast
vrouter running ipv4-multicast# as-override true|false
Default value
false
send-community

Send Community attribute to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast
vrouter running ipv4-multicast# send-community SEND-COMMUNITY
SEND-COMMUNITY values Description
all Send Standard and Extended Community attributes.
extended Send Extended Community attributes.
standard Send Standard Community attributes.
none Do not send Standard or Extended Community attributes.
Default value
all
weight

Set default weight for routes from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast
vrouter running ipv4-multicast# weight <uint16>
allowas-in

Accept as-path with my AS present in it.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast
vrouter running ipv4-multicast# allowas-in ALLOWAS-IN
ALLOWAS-IN values Description
<uint8> No description.
origin Only accept my AS in the as-path if the route was originated in my AS.
attribute-unchanged

BGP attribute is propagated unchanged to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast
vrouter running ipv4-multicast# attribute-unchanged ATTRIBUTE-UNCHANGED
ATTRIBUTE-UNCHANGED values Description
as-path As-path attribute.
med Med attribute.
nexthop Nexthop attribute.
route-server-client

If true, configure a neighbor as Route Server client.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast
vrouter running ipv4-multicast# route-server-client true|false
Default value
false
soft-reconfiguration-inbound

If true, allow inbound soft reconfiguration for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast
vrouter running ipv4-multicast# soft-reconfiguration-inbound true|false
Default value
false
route-reflector-client

If true, configure a neighbor as Route Reflector client.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast
vrouter running ipv4-multicast# route-reflector-client true|false
Default value
false
capability-orf-prefix-list

Advertise prefixlist ORF capability to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast
vrouter running ipv4-multicast# capability-orf-prefix-list CAPABILITY-ORF-PREFIX-LIST
CAPABILITY-ORF-PREFIX-LIST values Description
both Capability to SEND and RECEIVE the ORF to/from this neighbor.
send Capability to SEND the ORF to this neighbor.
receive Capability to RECEIVE the ORF from this neighbor.
unsuppress-map

Route-map to selectively unsuppress suppressed routes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast
vrouter running ipv4-multicast# unsuppress-map UNSUPPRESS-MAP
UNSUPPRESS-MAP Route map name.
update-group-id (state only)

Update group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast update-group-id
sub-group-id (state only)

Sub-group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast sub-group-id
packet-queue-length (state only)

Packet queue length.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast packet-queue-length
accepted-prefix (state only)

Accepted prefix counter.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast accepted-prefix
addpath

Configure addpath.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast addpath
tx-all-paths

If true, use addpath to advertise all paths to a neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast addpath
vrouter running addpath# tx-all-paths true|false
Default value
false
tx-best-path-per-AS

If true, use addpath to advertise the bestpath per each neighboring AS.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast addpath
vrouter running addpath# tx-best-path-per-AS true|false
Default value
false
distribute-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast
vrouter running ipv4-multicast# distribute-list <distribute-list> access-list ACCESS-LIST
<distribute-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list ACCESS-LIST
ACCESS-LIST Access list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast distribute-list <distribute-list> update-direction
maximum-prefix

Maximum number of prefixes to accept from this peer.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast maximum-prefix
maximum (mandatory)

Maximum number of prefix limit.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast maximum-prefix
vrouter running maximum-prefix# maximum <uint32>
threshold

Threshold value (%) at which to generate a warning msg.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast maximum-prefix
vrouter running maximum-prefix# threshold <uint8>
Default value
75
restart

Restart interval in minutes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast maximum-prefix
vrouter running maximum-prefix# restart <int16>
warning-only

If true, only give warning message when limit is exceeded.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast maximum-prefix
vrouter running maximum-prefix# warning-only true|false
Default value
false
nexthop-self

Disable the next hop calculation for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast nexthop-self
force

If true, set the next hop to self for reflected routes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast nexthop-self
vrouter running nexthop-self# force true|false
Default value
false
as-outbound-update

Remove or replace ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast as-outbound-update
action

Action to apply for ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast as-outbound-update
vrouter running as-outbound-update# action ACTION
ACTION values Description
replace Replace ASNs in outbound updates by our ASN.
remove Remove ASN in outbound updates.
Default value
remove
as-type

Apply to private AS numbers or all.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast as-outbound-update
vrouter running as-outbound-update# as-type AS-TYPE
AS-TYPE values Description
private Apply to private AS numbers only.
all Apply to all AS numbers.
Default value
private
filter-list

Establish BGP filters.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast
vrouter running ipv4-multicast# filter-list <filter-list> access-list <as-path-access-list...
<filter-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list <as-path-access-list>
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast filter-list <filter-list> update-direction
prefix-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast
vrouter running ipv4-multicast# prefix-list <prefix-list> prefix-list-name PREFIX-LIST-NAME
<prefix-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
prefix-list-name (mandatory)

Name of the prefix list.

prefix-list-name PREFIX-LIST-NAME
PREFIX-LIST-NAME Prefix list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast prefix-list <prefix-list> update-direction
route-map

Apply route map to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast
vrouter running ipv4-multicast# route-map <route-map> route-map-name ROUTE-MAP-NAME
<route-map> values Description
in Apply map to incoming routes.
out Apply map to outbound routes.
route-map-name (mandatory)

Route-map name.

route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME Route map name.
route-direction (state only)

Route direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast route-map <route-map> route-direction
default-originate

Originate default route to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast default-originate
route-map

Route-map to specify criteria to originate default.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-multicast default-originate
vrouter running default-originate# route-map ROUTE-MAP
ROUTE-MAP Route map name.

ipv4-labeled-unicast

IPv4 labeled unicast address-family associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast
enabled

Enable or disable IPv4 labeled unicast Address Family for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# enabled true|false
Default value
true
as-override

If true, disable checking if nexthop is connected on ebgp sessions.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# as-override true|false
Default value
false
send-community

Send Community attribute to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# send-community SEND-COMMUNITY
SEND-COMMUNITY values Description
all Send Standard and Extended Community attributes.
extended Send Extended Community attributes.
standard Send Standard Community attributes.
none Do not send Standard or Extended Community attributes.
Default value
all
weight

Set default weight for routes from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# weight <uint16>
allowas-in

Accept as-path with my AS present in it.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# allowas-in ALLOWAS-IN
ALLOWAS-IN values Description
<uint8> No description.
origin Only accept my AS in the as-path if the route was originated in my AS.
attribute-unchanged

BGP attribute is propagated unchanged to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# attribute-unchanged ATTRIBUTE-UNCHANGED
ATTRIBUTE-UNCHANGED values Description
as-path As-path attribute.
med Med attribute.
nexthop Nexthop attribute.
route-server-client

If true, configure a neighbor as Route Server client.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# route-server-client true|false
Default value
false
soft-reconfiguration-inbound

If true, allow inbound soft reconfiguration for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# soft-reconfiguration-inbound true|false
Default value
false
route-reflector-client

If true, configure a neighbor as Route Reflector client.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# route-reflector-client true|false
Default value
false
capability-orf-prefix-list

Advertise prefixlist ORF capability to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# capability-orf-prefix-list CAPABILITY-ORF-PREFIX-LIST
CAPABILITY-ORF-PREFIX-LIST values Description
both Capability to SEND and RECEIVE the ORF to/from this neighbor.
send Capability to SEND the ORF to this neighbor.
receive Capability to RECEIVE the ORF from this neighbor.
unsuppress-map

Route-map to selectively unsuppress suppressed routes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# unsuppress-map UNSUPPRESS-MAP
UNSUPPRESS-MAP Route map name.
update-group-id (state only)

Update group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast update-group-id
sub-group-id (state only)

Sub-group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast sub-group-id
packet-queue-length (state only)

Packet queue length.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast packet-queue-length
accepted-prefix (state only)

Accepted prefix counter.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast accepted-prefix
addpath

Configure addpath.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast addpath
tx-all-paths

If true, use addpath to advertise all paths to a neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast addpath
vrouter running addpath# tx-all-paths true|false
Default value
false
tx-best-path-per-AS

If true, use addpath to advertise the bestpath per each neighboring AS.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast addpath
vrouter running addpath# tx-best-path-per-AS true|false
Default value
false
distribute-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# distribute-list <distribute-list> access-list ACCESS-LIST
<distribute-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list ACCESS-LIST
ACCESS-LIST Access list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast distribute-list <distribute-list> update-direction
maximum-prefix

Maximum number of prefixes to accept from this peer.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast maximum-prefix
maximum (mandatory)

Maximum number of prefix limit.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast maximum-prefix
vrouter running maximum-prefix# maximum <uint32>
threshold

Threshold value (%) at which to generate a warning msg.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast maximum-prefix
vrouter running maximum-prefix# threshold <uint8>
Default value
75
restart

Restart interval in minutes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast maximum-prefix
vrouter running maximum-prefix# restart <int16>
warning-only

If true, only give warning message when limit is exceeded.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast maximum-prefix
vrouter running maximum-prefix# warning-only true|false
Default value
false
nexthop-self

Disable the next hop calculation for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast nexthop-self
force

If true, set the next hop to self for reflected routes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast nexthop-self
vrouter running nexthop-self# force true|false
Default value
false
as-outbound-update

Remove or replace ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast as-outbound-update
action

Action to apply for ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast as-outbound-update
vrouter running as-outbound-update# action ACTION
ACTION values Description
replace Replace ASNs in outbound updates by our ASN.
remove Remove ASN in outbound updates.
Default value
remove
as-type

Apply to private AS numbers or all.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast as-outbound-update
vrouter running as-outbound-update# as-type AS-TYPE
AS-TYPE values Description
private Apply to private AS numbers only.
all Apply to all AS numbers.
Default value
private
filter-list

Establish BGP filters.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# filter-list <filter-list> access-list <as-path-access-list...
<filter-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list <as-path-access-list>
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast filter-list <filter-list> update-direction
prefix-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# prefix-list <prefix-list> prefix-list-name PREFIX-LIST-NAME
<prefix-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
prefix-list-name (mandatory)

Name of the prefix list.

prefix-list-name PREFIX-LIST-NAME
PREFIX-LIST-NAME Prefix list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast prefix-list <prefix-list> update-direction
route-map

Apply route map to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast
vrouter running ipv4-labeled-unicast# route-map <route-map> route-map-name ROUTE-MAP-NAME
<route-map> values Description
in Apply map to incoming routes.
out Apply map to outbound routes.
route-map-name (mandatory)

Route-map name.

route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME Route map name.
route-direction (state only)

Route direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast route-map <route-map> route-direction
default-originate

Originate default route to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast default-originate
route-map

Route-map to specify criteria to originate default.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-labeled-unicast default-originate
vrouter running default-originate# route-map ROUTE-MAP
ROUTE-MAP Route map name.

ipv4-flowspec

IPv4 Flowspec address-family associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-flowspec
enabled

Enable or disable IPv4 Flowspec Address Family for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-flowspec
vrouter running ipv4-flowspec# enabled true|false
Default value
true
route-server-client

If true, configure a neighbor as Route Server client.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-flowspec
vrouter running ipv4-flowspec# route-server-client true|false
Default value
false
soft-reconfiguration-inbound

If true, allow inbound soft reconfiguration for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-flowspec
vrouter running ipv4-flowspec# soft-reconfiguration-inbound true|false
Default value
false
route-reflector-client

If true, configure a neighbor as Route Reflector client.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-flowspec
vrouter running ipv4-flowspec# route-reflector-client true|false
Default value
false
update-group-id (state only)

Update group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-flowspec update-group-id
sub-group-id (state only)

Sub-group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-flowspec sub-group-id
packet-queue-length (state only)

Packet queue length.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-flowspec packet-queue-length
accepted-prefix (state only)

Accepted prefix counter.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-flowspec accepted-prefix
filter-list

Establish BGP filters.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-flowspec
vrouter running ipv4-flowspec# filter-list <filter-list> access-list <as-path-access-list...
<filter-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list <as-path-access-list>
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-flowspec filter-list <filter-list> update-direction
prefix-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-flowspec
vrouter running ipv4-flowspec# prefix-list <prefix-list> prefix-list-name PREFIX-LIST-NAME
<prefix-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
prefix-list-name (mandatory)

Name of the prefix list.

prefix-list-name PREFIX-LIST-NAME
PREFIX-LIST-NAME Prefix list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-flowspec prefix-list <prefix-list> update-direction
route-map

Apply route map to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-flowspec
vrouter running ipv4-flowspec# route-map <route-map> route-map-name ROUTE-MAP-NAME
<route-map> values Description
in Apply map to incoming routes.
out Apply map to outbound routes.
route-map-name (mandatory)

Route-map name.

route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME Route map name.
route-direction (state only)

Route direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv4-flowspec route-map <route-map> route-direction

ipv6-unicast

IPv6 unicast address-family associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
enabled

Enable or disable IPv6 unicast Address Family for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
vrouter running ipv6-unicast# enabled true|false
Default value
true
nexthop-local-unchanged

If true, leave link-local nexthop unchanged for this peer.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
vrouter running ipv6-unicast# nexthop-local-unchanged true|false
Default value
false
as-override

If true, disable checking if nexthop is connected on ebgp sessions.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
vrouter running ipv6-unicast# as-override true|false
Default value
false
send-community

Send Community attribute to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
vrouter running ipv6-unicast# send-community SEND-COMMUNITY
SEND-COMMUNITY values Description
all Send Standard and Extended Community attributes.
extended Send Extended Community attributes.
standard Send Standard Community attributes.
none Do not send Standard or Extended Community attributes.
Default value
all
weight

Set default weight for routes from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
vrouter running ipv6-unicast# weight <uint16>
allowas-in

Accept as-path with my AS present in it.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
vrouter running ipv6-unicast# allowas-in ALLOWAS-IN
ALLOWAS-IN values Description
<uint8> No description.
origin Only accept my AS in the as-path if the route was originated in my AS.
attribute-unchanged

BGP attribute is propagated unchanged to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
vrouter running ipv6-unicast# attribute-unchanged ATTRIBUTE-UNCHANGED
ATTRIBUTE-UNCHANGED values Description
as-path As-path attribute.
med Med attribute.
nexthop Nexthop attribute.
route-server-client

If true, configure a neighbor as Route Server client.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
vrouter running ipv6-unicast# route-server-client true|false
Default value
false
soft-reconfiguration-inbound

If true, allow inbound soft reconfiguration for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
vrouter running ipv6-unicast# soft-reconfiguration-inbound true|false
Default value
false
route-reflector-client

If true, configure a neighbor as Route Reflector client.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
vrouter running ipv6-unicast# route-reflector-client true|false
Default value
false
capability-orf-prefix-list

Advertise prefixlist ORF capability to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
vrouter running ipv6-unicast# capability-orf-prefix-list CAPABILITY-ORF-PREFIX-LIST
CAPABILITY-ORF-PREFIX-LIST values Description
both Capability to SEND and RECEIVE the ORF to/from this neighbor.
send Capability to SEND the ORF to this neighbor.
receive Capability to RECEIVE the ORF from this neighbor.
unsuppress-map

Route-map to selectively unsuppress suppressed routes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
vrouter running ipv6-unicast# unsuppress-map UNSUPPRESS-MAP
UNSUPPRESS-MAP Route map name.
update-group-id (state only)

Update group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast update-group-id
sub-group-id (state only)

Sub-group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast sub-group-id
packet-queue-length (state only)

Packet queue length.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast packet-queue-length
accepted-prefix (state only)

Accepted prefix counter.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast accepted-prefix
addpath

Configure addpath.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast addpath
tx-all-paths

If true, use addpath to advertise all paths to a neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast addpath
vrouter running addpath# tx-all-paths true|false
Default value
false
tx-best-path-per-AS

If true, use addpath to advertise the bestpath per each neighboring AS.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast addpath
vrouter running addpath# tx-best-path-per-AS true|false
Default value
false
distribute-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
vrouter running ipv6-unicast# distribute-list <distribute-list> access-list ACCESS-LIST
<distribute-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list ACCESS-LIST
ACCESS-LIST Access list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast distribute-list <distribute-list> update-direction
maximum-prefix

Maximum number of prefixes to accept from this peer.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast maximum-prefix
maximum (mandatory)

Maximum number of prefix limit.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast maximum-prefix
vrouter running maximum-prefix# maximum <uint32>
threshold

Threshold value (%) at which to generate a warning msg.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast maximum-prefix
vrouter running maximum-prefix# threshold <uint8>
Default value
75
restart

Restart interval in minutes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast maximum-prefix
vrouter running maximum-prefix# restart <int16>
warning-only

If true, only give warning message when limit is exceeded.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast maximum-prefix
vrouter running maximum-prefix# warning-only true|false
Default value
false
nexthop-self

Disable the next hop calculation for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast nexthop-self
force

If true, set the next hop to self for reflected routes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast nexthop-self
vrouter running nexthop-self# force true|false
Default value
false
as-outbound-update

Remove or replace ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast as-outbound-update
action

Action to apply for ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast as-outbound-update
vrouter running as-outbound-update# action ACTION
ACTION values Description
replace Replace ASNs in outbound updates by our ASN.
remove Remove ASN in outbound updates.
Default value
remove
as-type

Apply to private AS numbers or all.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast as-outbound-update
vrouter running as-outbound-update# as-type AS-TYPE
AS-TYPE values Description
private Apply to private AS numbers only.
all Apply to all AS numbers.
Default value
private
filter-list

Establish BGP filters.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
vrouter running ipv6-unicast# filter-list <filter-list> access-list <as-path-access-list...
<filter-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list <as-path-access-list>
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast filter-list <filter-list> update-direction
prefix-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
vrouter running ipv6-unicast# prefix-list <prefix-list> prefix-list-name PREFIX-LIST-NAME
<prefix-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
prefix-list-name (mandatory)

Name of the prefix list.

prefix-list-name PREFIX-LIST-NAME
PREFIX-LIST-NAME Prefix list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast prefix-list <prefix-list> update-direction
route-map

Apply route map to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast
vrouter running ipv6-unicast# route-map <route-map> route-map-name ROUTE-MAP-NAME
<route-map> values Description
in Apply map to incoming routes.
out Apply map to outbound routes.
route-map-name (mandatory)

Route-map name.

route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME Route map name.
route-direction (state only)

Route direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast route-map <route-map> route-direction
default-originate

Originate default route to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast default-originate
route-map

Route-map to specify criteria to originate default.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-unicast default-originate
vrouter running default-originate# route-map ROUTE-MAP
ROUTE-MAP Route map name.

ipv6-multicast

IPv6 multicast address-family associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast
enabled

Enable or disable IPv6 multicast Address Family for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast
vrouter running ipv6-multicast# enabled true|false
Default value
true
as-override

If true, disable checking if nexthop is connected on ebgp sessions.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast
vrouter running ipv6-multicast# as-override true|false
Default value
false
send-community

Send Community attribute to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast
vrouter running ipv6-multicast# send-community SEND-COMMUNITY
SEND-COMMUNITY values Description
all Send Standard and Extended Community attributes.
extended Send Extended Community attributes.
standard Send Standard Community attributes.
none Do not send Standard or Extended Community attributes.
Default value
all
weight

Set default weight for routes from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast
vrouter running ipv6-multicast# weight <uint16>
allowas-in

Accept as-path with my AS present in it.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast
vrouter running ipv6-multicast# allowas-in ALLOWAS-IN
ALLOWAS-IN values Description
<uint8> No description.
origin Only accept my AS in the as-path if the route was originated in my AS.
attribute-unchanged

BGP attribute is propagated unchanged to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast
vrouter running ipv6-multicast# attribute-unchanged ATTRIBUTE-UNCHANGED
ATTRIBUTE-UNCHANGED values Description
as-path As-path attribute.
med Med attribute.
nexthop Nexthop attribute.
route-server-client

If true, configure a neighbor as Route Server client.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast
vrouter running ipv6-multicast# route-server-client true|false
Default value
false
soft-reconfiguration-inbound

If true, allow inbound soft reconfiguration for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast
vrouter running ipv6-multicast# soft-reconfiguration-inbound true|false
Default value
false
route-reflector-client

If true, configure a neighbor as Route Reflector client.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast
vrouter running ipv6-multicast# route-reflector-client true|false
Default value
false
capability-orf-prefix-list

Advertise prefixlist ORF capability to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast
vrouter running ipv6-multicast# capability-orf-prefix-list CAPABILITY-ORF-PREFIX-LIST
CAPABILITY-ORF-PREFIX-LIST values Description
both Capability to SEND and RECEIVE the ORF to/from this neighbor.
send Capability to SEND the ORF to this neighbor.
receive Capability to RECEIVE the ORF from this neighbor.
unsuppress-map

Route-map to selectively unsuppress suppressed routes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast
vrouter running ipv6-multicast# unsuppress-map UNSUPPRESS-MAP
UNSUPPRESS-MAP Route map name.
update-group-id (state only)

Update group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast update-group-id
sub-group-id (state only)

Sub-group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast sub-group-id
packet-queue-length (state only)

Packet queue length.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast packet-queue-length
accepted-prefix (state only)

Accepted prefix counter.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast accepted-prefix
addpath

Configure addpath.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast addpath
tx-all-paths

If true, use addpath to advertise all paths to a neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast addpath
vrouter running addpath# tx-all-paths true|false
Default value
false
tx-best-path-per-AS

If true, use addpath to advertise the bestpath per each neighboring AS.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast addpath
vrouter running addpath# tx-best-path-per-AS true|false
Default value
false
distribute-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast
vrouter running ipv6-multicast# distribute-list <distribute-list> access-list ACCESS-LIST
<distribute-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list ACCESS-LIST
ACCESS-LIST Access list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast distribute-list <distribute-list> update-direction
maximum-prefix

Maximum number of prefixes to accept from this peer.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast maximum-prefix
maximum (mandatory)

Maximum number of prefix limit.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast maximum-prefix
vrouter running maximum-prefix# maximum <uint32>
threshold

Threshold value (%) at which to generate a warning msg.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast maximum-prefix
vrouter running maximum-prefix# threshold <uint8>
Default value
75
restart

Restart interval in minutes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast maximum-prefix
vrouter running maximum-prefix# restart <int16>
warning-only

If true, only give warning message when limit is exceeded.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast maximum-prefix
vrouter running maximum-prefix# warning-only true|false
Default value
false
nexthop-self

Disable the next hop calculation for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast nexthop-self
force

If true, set the next hop to self for reflected routes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast nexthop-self
vrouter running nexthop-self# force true|false
Default value
false
as-outbound-update

Remove or replace ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast as-outbound-update
action

Action to apply for ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast as-outbound-update
vrouter running as-outbound-update# action ACTION
ACTION values Description
replace Replace ASNs in outbound updates by our ASN.
remove Remove ASN in outbound updates.
Default value
remove
as-type

Apply to private AS numbers or all.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast as-outbound-update
vrouter running as-outbound-update# as-type AS-TYPE
AS-TYPE values Description
private Apply to private AS numbers only.
all Apply to all AS numbers.
Default value
private
filter-list

Establish BGP filters.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast
vrouter running ipv6-multicast# filter-list <filter-list> access-list <as-path-access-list...
<filter-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list <as-path-access-list>
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast filter-list <filter-list> update-direction
prefix-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast
vrouter running ipv6-multicast# prefix-list <prefix-list> prefix-list-name PREFIX-LIST-NAME
<prefix-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
prefix-list-name (mandatory)

Name of the prefix list.

prefix-list-name PREFIX-LIST-NAME
PREFIX-LIST-NAME Prefix list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast prefix-list <prefix-list> update-direction
route-map

Apply route map to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast
vrouter running ipv6-multicast# route-map <route-map> route-map-name ROUTE-MAP-NAME
<route-map> values Description
in Apply map to incoming routes.
out Apply map to outbound routes.
route-map-name (mandatory)

Route-map name.

route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME Route map name.
route-direction (state only)

Route direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast route-map <route-map> route-direction
default-originate

Originate default route to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast default-originate
route-map

Route-map to specify criteria to originate default.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-multicast default-originate
vrouter running default-originate# route-map ROUTE-MAP
ROUTE-MAP Route map name.

ipv6-labeled-unicast

IPv6 labeled unicast address-family associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast
enabled

Enable or disable IPv6 labeled unicast Address Family for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# enabled true|false
Default value
true
as-override

If true, disable checking if nexthop is connected on ebgp sessions.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# as-override true|false
Default value
false
send-community

Send Community attribute to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# send-community SEND-COMMUNITY
SEND-COMMUNITY values Description
all Send Standard and Extended Community attributes.
extended Send Extended Community attributes.
standard Send Standard Community attributes.
none Do not send Standard or Extended Community attributes.
Default value
all
weight

Set default weight for routes from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# weight <uint16>
allowas-in

Accept as-path with my AS present in it.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# allowas-in ALLOWAS-IN
ALLOWAS-IN values Description
<uint8> No description.
origin Only accept my AS in the as-path if the route was originated in my AS.
attribute-unchanged

BGP attribute is propagated unchanged to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# attribute-unchanged ATTRIBUTE-UNCHANGED
ATTRIBUTE-UNCHANGED values Description
as-path As-path attribute.
med Med attribute.
nexthop Nexthop attribute.
route-server-client

If true, configure a neighbor as Route Server client.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# route-server-client true|false
Default value
false
soft-reconfiguration-inbound

If true, allow inbound soft reconfiguration for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# soft-reconfiguration-inbound true|false
Default value
false
route-reflector-client

If true, configure a neighbor as Route Reflector client.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# route-reflector-client true|false
Default value
false
capability-orf-prefix-list

Advertise prefixlist ORF capability to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# capability-orf-prefix-list CAPABILITY-ORF-PREFIX-LIST
CAPABILITY-ORF-PREFIX-LIST values Description
both Capability to SEND and RECEIVE the ORF to/from this neighbor.
send Capability to SEND the ORF to this neighbor.
receive Capability to RECEIVE the ORF from this neighbor.
unsuppress-map

Route-map to selectively unsuppress suppressed routes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# unsuppress-map UNSUPPRESS-MAP
UNSUPPRESS-MAP Route map name.
update-group-id (state only)

Update group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast update-group-id
sub-group-id (state only)

Sub-group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast sub-group-id
packet-queue-length (state only)

Packet queue length.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast packet-queue-length
accepted-prefix (state only)

Accepted prefix counter.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast accepted-prefix
addpath

Configure addpath.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast addpath
tx-all-paths

If true, use addpath to advertise all paths to a neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast addpath
vrouter running addpath# tx-all-paths true|false
Default value
false
tx-best-path-per-AS

If true, use addpath to advertise the bestpath per each neighboring AS.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast addpath
vrouter running addpath# tx-best-path-per-AS true|false
Default value
false
distribute-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# distribute-list <distribute-list> access-list ACCESS-LIST
<distribute-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list ACCESS-LIST
ACCESS-LIST Access list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast distribute-list <distribute-list> update-direction
maximum-prefix

Maximum number of prefixes to accept from this peer.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast maximum-prefix
maximum (mandatory)

Maximum number of prefix limit.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast maximum-prefix
vrouter running maximum-prefix# maximum <uint32>
threshold

Threshold value (%) at which to generate a warning msg.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast maximum-prefix
vrouter running maximum-prefix# threshold <uint8>
Default value
75
restart

Restart interval in minutes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast maximum-prefix
vrouter running maximum-prefix# restart <int16>
warning-only

If true, only give warning message when limit is exceeded.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast maximum-prefix
vrouter running maximum-prefix# warning-only true|false
Default value
false
nexthop-self

Disable the next hop calculation for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast nexthop-self
force

If true, set the next hop to self for reflected routes.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast nexthop-self
vrouter running nexthop-self# force true|false
Default value
false
as-outbound-update

Remove or replace ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast as-outbound-update
action

Action to apply for ASNs in outbound updates.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast as-outbound-update
vrouter running as-outbound-update# action ACTION
ACTION values Description
replace Replace ASNs in outbound updates by our ASN.
remove Remove ASN in outbound updates.
Default value
remove
as-type

Apply to private AS numbers or all.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast as-outbound-update
vrouter running as-outbound-update# as-type AS-TYPE
AS-TYPE values Description
private Apply to private AS numbers only.
all Apply to all AS numbers.
Default value
private
filter-list

Establish BGP filters.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# filter-list <filter-list> access-list <as-path-access-list...
<filter-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list <as-path-access-list>
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast filter-list <filter-list> update-direction
prefix-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# prefix-list <prefix-list> prefix-list-name PREFIX-LIST-NAME
<prefix-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
prefix-list-name (mandatory)

Name of the prefix list.

prefix-list-name PREFIX-LIST-NAME
PREFIX-LIST-NAME Prefix list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast prefix-list <prefix-list> update-direction
route-map

Apply route map to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast
vrouter running ipv6-labeled-unicast# route-map <route-map> route-map-name ROUTE-MAP-NAME
<route-map> values Description
in Apply map to incoming routes.
out Apply map to outbound routes.
route-map-name (mandatory)

Route-map name.

route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME Route map name.
route-direction (state only)

Route direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast route-map <route-map> route-direction
default-originate

Originate default route to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast default-originate
route-map

Route-map to specify criteria to originate default.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-labeled-unicast default-originate
vrouter running default-originate# route-map ROUTE-MAP
ROUTE-MAP Route map name.

ipv6-flowspec

IPv6 Flowspec address-family associated with the BGP neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-flowspec
enabled

Enable or disable IPv6 Flowspec Address Family for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-flowspec
vrouter running ipv6-flowspec# enabled true|false
Default value
true
route-server-client

If true, configure a neighbor as Route Server client.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-flowspec
vrouter running ipv6-flowspec# route-server-client true|false
Default value
false
soft-reconfiguration-inbound

If true, allow inbound soft reconfiguration for this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-flowspec
vrouter running ipv6-flowspec# soft-reconfiguration-inbound true|false
Default value
false
route-reflector-client

If true, configure a neighbor as Route Reflector client.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-flowspec
vrouter running ipv6-flowspec# route-reflector-client true|false
Default value
false
update-group-id (state only)

Update group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-flowspec update-group-id
sub-group-id (state only)

Sub-group identifier.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-flowspec sub-group-id
packet-queue-length (state only)

Packet queue length.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-flowspec packet-queue-length
accepted-prefix (state only)

Accepted prefix counter.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-flowspec accepted-prefix
filter-list

Establish BGP filters.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-flowspec
vrouter running ipv6-flowspec# filter-list <filter-list> access-list <as-path-access-list...
<filter-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
access-list (mandatory)

Access list name.

access-list <as-path-access-list>
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-flowspec filter-list <filter-list> update-direction
prefix-list

Filter updates to/from this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-flowspec
vrouter running ipv6-flowspec# prefix-list <prefix-list> prefix-list-name PREFIX-LIST-NAME
<prefix-list> values Description
in Filter incoming updates.
out Filter outgoing updates.
prefix-list-name (mandatory)

Name of the prefix list.

prefix-list-name PREFIX-LIST-NAME
PREFIX-LIST-NAME Prefix list name.
update-direction (state only)

Updates direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-flowspec prefix-list <prefix-list> update-direction
route-map

Apply route map to this neighbor.

vrouter running config# vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-flowspec
vrouter running ipv6-flowspec# route-map <route-map> route-map-name ROUTE-MAP-NAME
<route-map> values Description
in Apply map to incoming routes.
out Apply map to outbound routes.
route-map-name (mandatory)

Route-map name.

route-map-name ROUTE-MAP-NAME
ROUTE-MAP-NAME Route map name.
route-direction (state only)

Route direction.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> address-family ipv6-flowspec route-map <route-map> route-direction

connections (state only)

Established/dropped connections statistics.

established (state only)

Number of established connections.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> connections established

dropped (state only)

Number of dropped connections.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> connections dropped

local-host (state only)

Local host data.

name (state only)

Local host name.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> local-host name

port (state only)

Local host port.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> local-host port

remote-host (state only)

Remote host data.

name (state only)

Remote host name.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> remote-host name

port (state only)

Remote host port.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> remote-host port

nexthop (state only)

Nexthop data.

address (state only)

Nexthop IP address.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> nexthop address

global-address (state only)

Nexthop global IP address.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> nexthop global-address

local-address (state only)

Nexthop local IP address.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> nexthop local-address

thread (state only)

Read/Write thread.

read-enabled (state only)

Read thread status.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> thread read-enabled

write-enabled (state only)

Write thread status.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> thread write-enabled

message-statistics (state only)

Neighbor messages statistics.

packet-wait-process (state only)

Number of packets waiting to be processed.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> message-statistics packet-wait-process

packet-wait-written (state only)

Number of packets waiting to be written.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> message-statistics packet-wait-written

open-sent (state only)

BGP open messages sent.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> message-statistics open-sent

opens-received (state only)

BGP open messages received.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> message-statistics opens-received

notifications-sent (state only)

Notifications messages sent.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> message-statistics notifications-sent

notifications-received (state only)

Notification messages received.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> message-statistics notifications-received

updates-sent (state only)

Update messages sent.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> message-statistics updates-sent

updates-received (state only)

Update messages received.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> message-statistics updates-received

keepalives-sent (state only)

Keepalive messages sent.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> message-statistics keepalives-sent

keepalives-received (state only)

Keepalive messages received.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> message-statistics keepalives-received

route-refresh-sent (state only)

Route refresh messages sent.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> message-statistics route-refresh-sent

route-refresh-received (state only)

Route refresh messages received.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> message-statistics route-refresh-received

capability-sent (state only)

Capability messages sent.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> message-statistics capability-sent

capability-received (state only)

Capability messages received.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> message-statistics capability-received

total-sent (state only)

Total messages sent.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> message-statistics total-sent

total-received (state only)

Total messages received.

vrouter> show state vrf <vrf> routing bgp neighbor <neighbor> message-statistics total-received