xvrf¶
Note
requires a Product License.
The list of xvrf interfaces on the device.
vsr running config# vrf <vrf> interface xvrf <xvrf>
|
An interface name. |
mtu¶
Set the max transmission unit size in octets. IPv6 requires an MTU of 1280 octets or greater.
vsr running config# vrf <vrf> interface xvrf <xvrf>
vsr running xvrf <xvrf># mtu <uint32>
promiscuous¶
Set promiscuous mode.
vsr running config# vrf <vrf> interface xvrf <xvrf>
vsr running xvrf <xvrf># promiscuous true|false
enabled (pushed)¶
The desired (administrative) state of the interface.
vsr running config# vrf <vrf> interface xvrf <xvrf>
vsr running xvrf <xvrf># enabled true|false
- Default value
true
description¶
A textual description of the interface.
vsr running config# vrf <vrf> interface xvrf <xvrf>
vsr running xvrf <xvrf># description <string>
link-interface (mandatory)¶
The other endpoint of the xvrf pair.
vsr running config# vrf <vrf> interface xvrf <xvrf>
vsr running xvrf <xvrf># link-interface LINK-INTERFACE
|
Description |
|---|---|
|
No description. |
|
No description. |
link-vrf (mandatory)¶
The link vrf name.
vsr running config# vrf <vrf> interface xvrf <xvrf>
vsr running xvrf <xvrf># link-vrf <string>
ifindex (state only)¶
System assigned number for each interface. Corresponds to ifIndex object in SNMP Interface MIB.
vsr> show state vrf <vrf> interface xvrf <xvrf> ifindex
admin-status (state only)¶
The desired state of the interface. In RFC 7223 this leaf has the same read semantics as ifAdminStatus. Here, it reflects the administrative state as set by enabling or disabling the interface.
vsr> show state vrf <vrf> interface xvrf <xvrf> admin-status
oper-status (state only) (pushed)¶
The current operational state of the interface. This leaf has the same semantics as ifOperStatus.
vsr> show state vrf <vrf> interface xvrf <xvrf> oper-status
last-change (state only)¶
unit: nanoseconds
This timestamp indicates the time of the last state change of the interface (e.g., up-to-down transition). This corresponds to the ifLastChange object in the standard interface MIB. The value is the timestamp in nanoseconds relative to the Unix Epoch (Jan 1, 1970 00:00:00 UTC).
vsr> show state vrf <vrf> interface xvrf <xvrf> last-change
ddos-protection (deprecated)¶
Note
requires a DDoS protection License.
Configuration for anti DDoS protection.
vsr running config# vrf <vrf> interface xvrf <xvrf> ddos-protection
enabled (deprecated)¶
Enable anti-DDoS Protection.
vsr running config# vrf <vrf> interface xvrf <xvrf> ddos-protection
vsr running ddos-protection# enabled true|false
qos¶
Note
requires a Product License.
QoS configuration.
vsr running config# vrf <vrf> interface xvrf <xvrf> qos
ingress¶
Ingress QoS configuration.
vsr running config# vrf <vrf> interface xvrf <xvrf> qos ingress
policy (config only)¶
List of QoS policies defined in the QoS context.
vsr running config# vrf <vrf> interface xvrf <xvrf> qos ingress
vsr running ingress# policy <leafref>
rate-limit¶
Rate limit configuration.
vsr running config# vrf <vrf> interface xvrf <xvrf> qos ingress rate-limit
policer (config only)¶
Traffic policer defined in the QoS context.
vsr running config# vrf <vrf> interface xvrf <xvrf> qos ingress rate-limit
vsr running rate-limit# policer <leafref>
policer (state only)¶
Traffic policer.
bandwidth (state only)¶
Maximum bandwidth of regular traffic, a.k.a. CIR (Committed Information Rate), in bps. 0 allows no regular traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress rate-limit policer bandwidth
burst (state only)¶
Maximum burst size of shaped traffic, a.k.a. CBS (Committed Burst Size), in bytes. The default value is set to bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress rate-limit policer burst
excess-bandwidth (state only)¶
Maximum bandwidth of excess traffic, a.k.a. EIR (Excess Information Rate), in bps. 0 allows no excess traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress rate-limit policer excess-bandwidth
excess-burst (state only)¶
Maximum burst size of excess traffic, a.k.a. EBS (Excess Burst Size), in bytes. The default value is set to excess-bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress rate-limit policer excess-burst
stats (state only)¶
Traffic policer statistics.
Number of packets passed (regular traffic that conforms to (bandwidth, burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress rate-limit policer stats pass-packets
Number of bytes passed (regular traffic that conforms to (bandwidth, burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress rate-limit policer stats pass-bytes
Number of excess packets passed (excess traffic that conforms to (excess-bandwidth, excess-burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress rate-limit policer stats pass-excess-packets
Number of excess bytes passed (excess traffic that conforms to (excess-bandwidth, excess-burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress rate-limit policer stats pass-excess-bytes
Number of packets dropped (traffic that does not conform to bandwidth or excess-bandwidth).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress rate-limit policer stats drop-packets
Number of bytes dropped (traffic that does not conform to bandwidth or excess-bandwidth).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress rate-limit policer stats drop-bytes
policy (state only)¶
List of QoS policies.
priority (state only)¶
Priority of the policy (policies are looked up hacked by increasing order of priority).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> priority
selector (state only)¶
List of traffic selectors.
match8bits (state only)¶
8 bit selector.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> match8bits value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> match8bits mask
The offset in the frame where the value must match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> match8bits offset
match16bits (state only)¶
16 bit selector.
The 16 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> match16bits value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> match16bits mask
The offset in the frame where the value must match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> match16bits offset
match32bits (state only)¶
32 bit selector.
The 32 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> match32bits value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> match32bits mask
The offset in the frame where the value must match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> match32bits offset
ipv4 (state only)¶
IPv4 header selector.
Match all IPv4 traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> ipv4 match-all
The source address to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> ipv4 source
The destination address to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> ipv4 destination
The protocol to match.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> ipv4 protocol value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> ipv4 protocol mask
The TOS field to match.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> ipv4 tos value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> ipv4 tos mask
ipv6 (state only)¶
IPv6 header selector.
Match all IPv6 traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> ipv6 match-all
The source address to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> ipv6 source
The destination address to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> ipv6 destination
The protocol to match.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> ipv6 protocol value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> ipv6 protocol mask
The TC field to match.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> ipv6 tos value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> ipv6 tos mask
tcp (state only)¶
TCP header selector.
Match all TCP traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> tcp match-all
The source port to match.
The 16 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> tcp source-port value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> tcp source-port mask
The destination port to match.
The 16 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> tcp destination-port value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> tcp destination-port mask
udp (state only)¶
UDP header selector.
Match all UDP traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> udp match-all
The source port to match.
The 16 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> udp source-port value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> udp source-port mask
The destination port to match.
The 16 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> udp destination-port value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> udp destination-port mask
icmp (state only)¶
ICMP header selector.
Match all ICMP traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> icmp match-all
The ICMP type to match.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> icmp type value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> icmp type mask
The ICMP code to match.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> icmp code value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> icmp code mask
icmpv6 (state only)¶
ICMPv6 header selector.
Match all ICMPv6 traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> icmpv6 match-all
The ICMPv6 type to match.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> icmpv6 type value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> icmpv6 type mask
The ICMPv6 code to match.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> icmpv6 code value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> selector <string> icmpv6 code mask
action (state only)¶
The policy action.
set-mark (state only)¶
Mark the packet.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> action set-mark
restore-connmark (state only)¶
Copy the connection mark (ctmark) to the packet mark (nfmark): if the packet belongs to a connection in the conntrack module and a ctmark is assigned to this connection, then the mark is copied to the packet nfmark. Otherwise the packet nfmark is reset to 0.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> action restore-connmark
redirect (state only)¶
Redirect the packet to a QoS-hub interface.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> action redirect
pass (state only)¶
Do not apply any specific QoS processing.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> action pass
set-priority (state only)¶
Set the priority of the packet.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> action set-priority
stats (state only)¶
Policy statistics.
match-packets (state only)¶
Number of packets matched.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> stats match-packets
drop-packets (state only)¶
Number of packets dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos ingress policy <string> stats drop-packets
egress¶
Egress QoS configuration.
vsr running config# vrf <vrf> interface xvrf <xvrf> qos egress
scheduler (config only)¶
Scheduler defined in the QoS context.
vsr running config# vrf <vrf> interface xvrf <xvrf> qos egress
vsr running egress# scheduler <leafref>
policy (config only)¶
List of QoS policies defined in the QoS context.
vsr running config# vrf <vrf> interface xvrf <xvrf> qos egress
vsr running egress# policy <leafref>
rate-limit¶
Rate limit configuration.
vsr running config# vrf <vrf> interface xvrf <xvrf> qos egress rate-limit
policer (config only)¶
Traffic policer defined in the QoS context.
vsr running config# vrf <vrf> interface xvrf <xvrf> qos egress rate-limit
vsr running rate-limit# policer <leafref>
shaper (config only)¶
Traffic shaper defined in the QoS context.
vsr running config# vrf <vrf> interface xvrf <xvrf> qos egress rate-limit
vsr running rate-limit# shaper <leafref>
policer (state only)¶
Traffic policer.
bandwidth (state only)¶
Maximum bandwidth of regular traffic, a.k.a. CIR (Committed Information Rate), in bps. 0 allows no regular traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress rate-limit policer bandwidth
burst (state only)¶
Maximum burst size of shaped traffic, a.k.a. CBS (Committed Burst Size), in bytes. The default value is set to bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress rate-limit policer burst
excess-bandwidth (state only)¶
Maximum bandwidth of excess traffic, a.k.a. EIR (Excess Information Rate), in bps. 0 allows no excess traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress rate-limit policer excess-bandwidth
excess-burst (state only)¶
Maximum burst size of excess traffic, a.k.a. EBS (Excess Burst Size), in bytes. The default value is set to excess-bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress rate-limit policer excess-burst
stats (state only)¶
Traffic policer statistics.
Number of packets passed (regular traffic that conforms to (bandwidth, burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress rate-limit policer stats pass-packets
Number of bytes passed (regular traffic that conforms to (bandwidth, burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress rate-limit policer stats pass-bytes
Number of excess packets passed (excess traffic that conforms to (excess-bandwidth, excess-burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress rate-limit policer stats pass-excess-packets
Number of excess bytes passed (excess traffic that conforms to (excess-bandwidth, excess-burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress rate-limit policer stats pass-excess-bytes
Number of packets dropped (traffic that does not conform to bandwidth or excess-bandwidth).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress rate-limit policer stats drop-packets
Number of bytes dropped (traffic that does not conform to bandwidth or excess-bandwidth).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress rate-limit policer stats drop-bytes
shaper (state only)¶
Traffic shaper.
bandwidth (state only)¶
Maximum bandwidth of shaped traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress rate-limit shaper bandwidth
burst (state only)¶
Maximum burst size of shaped traffic. The default value is set to bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress rate-limit shaper burst
layer1-overhead (state only)¶
Number of bytes added by the underlying protocol on each packet.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress rate-limit shaper layer1-overhead
queue-size (state only)¶
Number of packets that can be saved in the delay queue. If a scheduler is also configured on the interface, this value is not used, the queues of the scheduler are used as delay queues. The value is rounded up to the nearest power of 2.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress rate-limit shaper queue-size
stats (state only)¶
Traffic shaper statistics.
Number of packets sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress rate-limit shaper stats pass-packets
Number of packets dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress rate-limit shaper stats drop-packets
scheduler (state only)¶
List of schedulers on an interface.
is-root (state only)¶
Is true if the scheduler is root on the interface.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> is-root
template-name (state only)¶
The template name it has been configured with.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> template-name
pq (state only)¶
Priority Queueing state.
nb-queue (state only)¶
Number of Priority Queueing queues available in the scheduler.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq nb-queue
default-queue (state only)¶
The scheduler queue on which the default traffic will be directed.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq default-queue
stats (state only)¶
Traffic pq scheduler statistics.
Number of packets enqueued.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq stats enqueue-packets
Number of bytes enqueued.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq stats enqueue-bytes
Number of packets sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq stats xmit-packets
Number of bytes sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq stats xmit-bytes
Number of packets dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq stats drop-queue-full
Number of bytes dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq stats drop-queue-full-bytes
queue (state only)¶
List of Priority Queueing queues.
Size of the queue in packets. The value is rounded up to the nearest power of 2.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> size
Child scheduler id within the interface.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> child-scheduler-id
Custom priority of this queue.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> priority
Queue’s input policer.
Maximum bandwidth of regular traffic, a.k.a. CIR (Committed Information Rate), in bps. 0 allows no regular traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> policer bandwidth
Maximum burst size of shaped traffic, a.k.a. CBS (Committed Burst Size), in bytes. The default value is set to bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> policer burst
Maximum bandwidth of excess traffic, a.k.a. EIR (Excess Information Rate), in bps. 0 allows no excess traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> policer excess-bandwidth
Maximum burst size of excess traffic, a.k.a. EBS (Excess Burst Size), in bytes. The default value is set to excess-bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> policer excess-burst
Queue’s input policer statistics.
Number of packets passed (regular traffic that conforms to (bandwidth, burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> policer stats pass-packets
Number of bytes passed (regular traffic that conforms to (bandwidth, burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> policer stats pass-bytes
Number of excess packets passed (excess traffic that conforms to (excess-bandwidth, excess-burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> policer stats pass-excess-packets
Number of excess bytes passed (excess traffic that conforms to (excess-bandwidth, excess-burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> policer stats pass-excess-bytes
Number of packets dropped (traffic that does not conform to bandwidth or excess-bandwidth).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> policer stats drop-packets
Number of bytes dropped (traffic that does not conform to bandwidth or excess-bandwidth).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> policer stats drop-bytes
Queue’s output shaper.
Maximum bandwidth of shaped traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> shaper bandwidth
Maximum burst size of shaped traffic. The default value is set to bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> shaper burst
Number of bytes added by the underlying protocol on each packet.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> shaper layer1-overhead
Number of packets that can be saved in the delay queue. If a scheduler is also configured on the interface, this value is not used, the queues of the scheduler are used as delay queues. The value is rounded up to the nearest power of 2.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> shaper queue-size
Queue’s output shaper statistics.
Number of packets sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> shaper stats pass-packets
Number of packets dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> shaper stats drop-packets
Classes assigned to the queue.
Queue statistics.
Number of packets enqueued.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> stats enqueue-packets
Number of bytes enqueued.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> stats enqueue-bytes
Number of packets sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> stats xmit-packets
Number of bytes sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> stats xmit-bytes
Number of packets dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> stats drop-queue-full
Number of bytes dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pq queue <uint32> stats drop-queue-full-bytes
pb-dwrr (state only)¶
Priority-Based Deficit Weighted Round Robin description.
nb-queue (state only)¶
Number of PB-DWRR queues available in the scheduler.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr nb-queue
default-queue (state only)¶
The scheduler queue on which the default traffic will be directed.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr default-queue
stats (state only)¶
Traffic pb-dwrr scheduler statistics.
Number of packets enqueued.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr stats enqueue-packets
Number of bytes enqueued.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr stats enqueue-bytes
Number of packets sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr stats xmit-packets
Number of bytes sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr stats xmit-bytes
Number of packets dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr stats drop-queue-full
Number of bytes dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr stats drop-queue-full-bytes
queue (state only)¶
List of PB-DWRR queues.
Size of the queue in packets. The value is rounded up to the nearest power of 2.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> size
Child scheduler id within the interface.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> child-scheduler-id
Quantum of the queue in bytes. Relevant only if priority is low.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> quantum
Priority of the queue (low or high).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> priority
Queue’s input policer.
Maximum bandwidth of regular traffic, a.k.a. CIR (Committed Information Rate), in bps. 0 allows no regular traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> policer bandwidth
Maximum burst size of shaped traffic, a.k.a. CBS (Committed Burst Size), in bytes. The default value is set to bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> policer burst
Maximum bandwidth of excess traffic, a.k.a. EIR (Excess Information Rate), in bps. 0 allows no excess traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> policer excess-bandwidth
Maximum burst size of excess traffic, a.k.a. EBS (Excess Burst Size), in bytes. The default value is set to excess-bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> policer excess-burst
Queue’s input policer statistics.
Number of packets passed (regular traffic that conforms to (bandwidth, burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> policer stats pass-packets
Number of bytes passed (regular traffic that conforms to (bandwidth, burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> policer stats pass-bytes
Number of excess packets passed (excess traffic that conforms to (excess-bandwidth, excess-burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> policer stats pass-excess-packets
Number of excess bytes passed (excess traffic that conforms to (excess-bandwidth, excess-burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> policer stats pass-excess-bytes
Number of packets dropped (traffic that does not conform to bandwidth or excess-bandwidth).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> policer stats drop-packets
Number of bytes dropped (traffic that does not conform to bandwidth or excess-bandwidth).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> policer stats drop-bytes
Queue’s output shaper.
Maximum bandwidth of shaped traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> shaper bandwidth
Maximum burst size of shaped traffic. The default value is set to bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> shaper burst
Number of bytes added by the underlying protocol on each packet.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> shaper layer1-overhead
Number of packets that can be saved in the delay queue. If a scheduler is also configured on the interface, this value is not used, the queues of the scheduler are used as delay queues. The value is rounded up to the nearest power of 2.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> shaper queue-size
Queue’s output shaper statistics.
Number of packets sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> shaper stats pass-packets
Number of packets dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> shaper stats drop-packets
Classes assigned to the queue.
Queue statistics.
Number of packets enqueued.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> stats enqueue-packets
Number of bytes enqueued.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> stats enqueue-bytes
Number of packets sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> stats xmit-packets
Number of bytes sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> stats xmit-bytes
Number of packets dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> stats drop-queue-full
Number of bytes dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> pb-dwrr queue <uint32> stats drop-queue-full-bytes
htb (state only)¶
Hierarchical Token Bucket description.
nb-queue (state only)¶
Current number of HTB queues in the scheduler.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb nb-queue
default-queue (state only)¶
The scheduler queue on which the default traffic will be directed.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb default-queue
divisor (state only)¶
Divisor used to calculate the default quantum of queues.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb divisor
stats (state only)¶
Traffic pq scheduler statistics.
Number of packets enqueued.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb stats enqueue-packets
Number of bytes enqueued.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb stats enqueue-bytes
Number of packets sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb stats xmit-packets
Number of bytes sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb stats xmit-bytes
Number of packets dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb stats drop-queue-full
Number of bytes dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb stats drop-queue-full-bytes
queue (state only)¶
List of HTB queues.
Size of the queue in packets. The value is rounded up to the nearest power of 2.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> size
Child scheduler id within the interface.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> child-scheduler-id
Guaranteed bandwidth of the queue (bps).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> bandwidth
Guaranteed bandwidth maximum burst size (bytes).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> burst
Ceiling rate of the queue (bps).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> ceiling
Ceiling rate maximum burst size (bytes).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> ceiling-burst
Priority of the queue in case of ceiling, used to distribute available ceiling bandwidth to queues by order of priority. Lower is more priority.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> ceiling-priority
Number of bytes added by the underlying protocol on each packet.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> layer1-overhead
Quantum of the queue, used to distribute available bandwidth between queues of same priorities, in a weighted round robin fashion.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> quantum
Attention
ceiling-priorityPriority of the queue, used to distribute available bandwidth to queues by order of priority.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> priority
List of child HTB queue IDs.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> child-queue
Queue’s input policer.
Maximum bandwidth of regular traffic, a.k.a. CIR (Committed Information Rate), in bps. 0 allows no regular traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> policer bandwidth
Maximum burst size of shaped traffic, a.k.a. CBS (Committed Burst Size), in bytes. The default value is set to bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> policer burst
Maximum bandwidth of excess traffic, a.k.a. EIR (Excess Information Rate), in bps. 0 allows no excess traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> policer excess-bandwidth
Maximum burst size of excess traffic, a.k.a. EBS (Excess Burst Size), in bytes. The default value is set to excess-bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> policer excess-burst
Queue’s input policer statistics.
Number of packets passed (regular traffic that conforms to (bandwidth, burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> policer stats pass-packets
Number of bytes passed (regular traffic that conforms to (bandwidth, burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> policer stats pass-bytes
Number of excess packets passed (excess traffic that conforms to (excess-bandwidth, excess-burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> policer stats pass-excess-packets
Number of excess bytes passed (excess traffic that conforms to (excess-bandwidth, excess-burst) specification.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> policer stats pass-excess-bytes
Number of packets dropped (traffic that does not conform to bandwidth or excess-bandwidth).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> policer stats drop-packets
Number of bytes dropped (traffic that does not conform to bandwidth or excess-bandwidth).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> policer stats drop-bytes
Queue’s output shaper.
Maximum bandwidth of shaped traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> shaper bandwidth
Maximum burst size of shaped traffic. The default value is set to bandwidth / 80 to handle a burst of 100 ms at the targeted bandwidth. If not set or set to 0, the default value is applied.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> shaper burst
Number of bytes added by the underlying protocol on each packet.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> shaper layer1-overhead
Number of packets that can be saved in the delay queue. If a scheduler is also configured on the interface, this value is not used, the queues of the scheduler are used as delay queues. The value is rounded up to the nearest power of 2.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> shaper queue-size
Queue’s output shaper statistics.
Number of packets sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> shaper stats pass-packets
Number of packets dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> shaper stats drop-packets
Classes assigned to the queue.
Queue statistics.
Number of packets enqueued.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> stats enqueue-packets
Number of bytes enqueued.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> stats enqueue-bytes
Number of packets sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> stats xmit-packets
Number of bytes sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> stats xmit-bytes
Number of packets dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> stats drop-queue-full
Number of bytes dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> htb queue <uint32> stats drop-queue-full-bytes
sfq (state only)¶
Stochastic Fair Queuing description.
flows (state only)¶
Number of flows in which the traffic is distributed.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> sfq flows
quantum (state only)¶
Amount of bytes a flow is allowed to dequeue during a round of the round robin process.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> sfq quantum
limit (state only)¶
Maximum number of packets that may be enqueued. If the limit is exceeded, half of the fattest flow packets are dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> sfq limit
stats (state only)¶
Traffic sfq scheduler statistics.
Number of packets enqueued.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> sfq stats enqueue-packets
Number of bytes enqueued.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> sfq stats enqueue-bytes
Number of packets sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> sfq stats xmit-packets
Number of bytes sent.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> sfq stats xmit-bytes
Number of packets dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> sfq stats drop-queue-full
Number of bytes dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress scheduler <uint32> sfq stats drop-queue-full-bytes
policy (state only)¶
List of QoS policies.
priority (state only)¶
Priority of the policy (policies are looked up hacked by increasing order of priority).
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> priority
selector (state only)¶
List of traffic selectors.
match8bits (state only)¶
8 bit selector.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> match8bits value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> match8bits mask
The offset in the frame where the value must match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> match8bits offset
match16bits (state only)¶
16 bit selector.
The 16 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> match16bits value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> match16bits mask
The offset in the frame where the value must match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> match16bits offset
match32bits (state only)¶
32 bit selector.
The 32 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> match32bits value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> match32bits mask
The offset in the frame where the value must match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> match32bits offset
ipv4 (state only)¶
IPv4 header selector.
Match all IPv4 traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> ipv4 match-all
The source address to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> ipv4 source
The destination address to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> ipv4 destination
The protocol to match.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> ipv4 protocol value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> ipv4 protocol mask
The TOS field to match.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> ipv4 tos value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> ipv4 tos mask
ipv6 (state only)¶
IPv6 header selector.
Match all IPv6 traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> ipv6 match-all
The source address to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> ipv6 source
The destination address to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> ipv6 destination
The protocol to match.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> ipv6 protocol value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> ipv6 protocol mask
The TC field to match.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> ipv6 tos value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> ipv6 tos mask
tcp (state only)¶
TCP header selector.
Match all TCP traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> tcp match-all
The source port to match.
The 16 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> tcp source-port value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> tcp source-port mask
The destination port to match.
The 16 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> tcp destination-port value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> tcp destination-port mask
udp (state only)¶
UDP header selector.
Match all UDP traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> udp match-all
The source port to match.
The 16 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> udp source-port value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> udp source-port mask
The destination port to match.
The 16 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> udp destination-port value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> udp destination-port mask
icmp (state only)¶
ICMP header selector.
Match all ICMP traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> icmp match-all
The ICMP type to match.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> icmp type value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> icmp type mask
The ICMP code to match.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> icmp code value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> icmp code mask
icmpv6 (state only)¶
ICMPv6 header selector.
Match all ICMPv6 traffic.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> icmpv6 match-all
The ICMPv6 type to match.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> icmpv6 type value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> icmpv6 type mask
The ICMPv6 code to match.
The 8 bit value to match.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> icmpv6 code value
Mask applied to value.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> selector <string> icmpv6 code mask
action (state only)¶
The policy action.
set-mark (state only)¶
Mark the packet.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> action set-mark
restore-connmark (state only)¶
Copy the connection mark (ctmark) to the packet mark (nfmark): if the packet belongs to a connection in the conntrack module and a ctmark is assigned to this connection, then the mark is copied to the packet nfmark. Otherwise the packet nfmark is reset to 0.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> action restore-connmark
redirect (state only)¶
Redirect the packet to a QoS-hub interface.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> action redirect
pass (state only)¶
Do not apply any specific QoS processing.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> action pass
set-priority (state only)¶
Set the priority of the packet.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> action set-priority
stats (state only)¶
Policy statistics.
match-packets (state only)¶
Number of packets matched.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> stats match-packets
drop-packets (state only)¶
Number of packets dropped.
vsr> show state vrf <vrf> interface xvrf <xvrf> qos egress policy <string> stats drop-packets
counters (state only)¶
A collection of interface-related statistics objects.
in-octets (state only)¶
The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ‘last-clear’.
vsr> show state vrf <vrf> interface xvrf <xvrf> counters in-octets
in-unicast-pkts (state only)¶
The number of packets, delivered by this sub-layer to a higher (sub-)layer, that were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ‘last-clear’.
vsr> show state vrf <vrf> interface xvrf <xvrf> counters in-unicast-pkts
in-discards (state only)¶
The number of inbound packets that were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ‘last-clear’.
vsr> show state vrf <vrf> interface xvrf <xvrf> counters in-discards
in-errors (state only)¶
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher- layer protocol. For character- oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of ‘last-clear’.
vsr> show state vrf <vrf> interface xvrf <xvrf> counters in-errors
out-octets (state only)¶
The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ‘last-clear’.
vsr> show state vrf <vrf> interface xvrf <xvrf> counters out-octets
out-unicast-pkts (state only)¶
The total number of packets that higher-level protocols requested be transmitted, and that were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of ‘last-clear’.
vsr> show state vrf <vrf> interface xvrf <xvrf> counters out-unicast-pkts
out-discards (state only)¶
The number of outbound packets that were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ‘last-clear’.
vsr> show state vrf <vrf> interface xvrf <xvrf> counters out-discards
out-errors (state only)¶
For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ‘last-clear’.
vsr> show state vrf <vrf> interface xvrf <xvrf> counters out-errors