3.2.26. interface

• bridge
  • mtu
  • promiscuous
  • enabled (pushed)
  • description
  • ageing-time
  • ifindex (state only)
  • admin-status (state only)
  • oper-status (state only)
  • last-change (state only)
  • ipv4
    • enabled
    • address
      • peer
      • origin (state only)
    • neighbor
      • link-layer-address (mandatory)
      • state (state only)
    • dhcp
      • enabled
      • timeout
      • retry
      • select-timeout
      • reboot
      • initial-interval
      • dhcp-lease-time
      • dhcp-client-identifier-ascii
      • dhcp-client-identifier-hexa
      • host-name
      • request
      • current-lease (state only)
        • fixed-address (state only)
        • renew (state only)
        • rebind (state only)
        • expire (state only)
  • ethernet
    • mac-address (pushed)
  • ipv6
    • enabled
    • address
      • peer
      • origin (state only)
      • status (state only)
    • neighbor
      • link-layer-address (mandatory)
      • router (state only)
      • state (state only)
  • network-stack
    • ipv4
      • send-redirects
      • accept-redirects
      • accept-source-route
      • arp-announce
      • arp-filter
      • arp-ignore
      • arp-proxy
      • log-invalid-addresses
    • ipv6
      • autoconfiguration
      • accept-duplicate-address-detection
      • accept-router-advert
      • accept-redirects
      • accept-segment-routing
      • accept-source-route
      • router-solicitations
      • use-temporary-addresses
  • stp
    • enabled
    • priority
    • forward-delay
    • max-age
    • hello-time
  • link-interface
    • learning
  • qos
    • ingress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
    • egress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
  • counters (state only)
    • in-octets (state only)
    • in-unicast-pkts (state only)
    • in-discards (state only)
    • in-errors (state only)
    • out-octets (state only)
    • out-unicast-pkts (state only)
    • out-discards (state only)
    • out-errors (state only)
• gre
  • mtu
  • promiscuous
  • enabled (pushed)
  • description
  • ttl
  • tos
  • link-interface
  • link-vrf
  • local (mandatory)
  • remote
  • checksum
  • sequence-number
  • ifindex (state only)
  • admin-status (state only)
  • oper-status (state only)
  • last-change (state only)
  • ipv4
    • enabled
    • address
      • peer
      • origin (state only)
    • neighbor
      • link-layer-address (mandatory)
      • state (state only)
  • ipv6
    • enabled
    • address
      • peer
      • origin (state only)
      • status (state only)
    • neighbor
      • link-layer-address (mandatory)
      • state (state only)
  • network-stack
    • ipv4
      • send-redirects
      • accept-redirects
      • accept-source-route
      • arp-announce
      • arp-filter
      • arp-ignore
      • arp-proxy
      • log-invalid-addresses
    • ipv6
      • autoconfiguration
      • accept-duplicate-address-detection
      • accept-router-advert
      • accept-redirects
      • accept-segment-routing
      • accept-source-route
      • router-solicitations
      • use-temporary-addresses
  • key
    • input (hidden)
    • output (hidden)
    • both (hidden)
  • qos
    • ingress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
    • egress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
  • counters (state only)
    • in-octets (state only)
    • in-unicast-pkts (state only)
    • in-discards (state only)
    • in-errors (state only)
    • out-octets (state only)
    • out-unicast-pkts (state only)
    • out-discards (state only)
    • out-errors (state only)
• gretap
  • mtu
  • promiscuous
  • enabled (pushed)
  • description
  • ttl
  • tos
  • link-interface
  • link-vrf
  • local (mandatory)
  • remote
  • checksum
  • sequence-number
  • ifindex (state only)
  • admin-status (state only)
  • oper-status (state only)
  • last-change (state only)
  • ipv4
    • enabled
    • address
      • peer
      • origin (state only)
    • neighbor
      • link-layer-address (mandatory)
      • state (state only)
  • ipv6
    • enabled
    • address
      • peer
      • origin (state only)
      • status (state only)
    • neighbor
      • link-layer-address (mandatory)
      • state (state only)
  • network-stack
    • ipv4
      • send-redirects
      • accept-redirects
      • accept-source-route
      • arp-announce
      • arp-filter
      • arp-ignore
      • arp-proxy
      • log-invalid-addresses
    • ipv6
      • autoconfiguration
      • accept-duplicate-address-detection
      • accept-router-advert
      • accept-redirects
      • accept-segment-routing
      • accept-source-route
      • router-solicitations
      • use-temporary-addresses
  • ethernet
    • mac-address (pushed)
  • key
    • input (hidden)
    • output (hidden)
    • both (hidden)
  • qos
    • ingress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
    • egress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
  • counters (state only)
    • in-octets (state only)
    • in-unicast-pkts (state only)
    • in-discards (state only)
    • in-errors (state only)
    • out-octets (state only)
    • out-unicast-pkts (state only)
    • out-discards (state only)
    • out-errors (state only)
• qos-hub
  • mtu
  • promiscuous
  • enabled (pushed)
  • description
  • ifindex (state only)
  • admin-status (state only)
  • oper-status (state only)
  • last-change (state only)
  • qos
    • ingress
      • policy (config only)
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
      • policy (state only)
        • priority (state only)
        • selector (state only)
          • match8bits (state only)
            • value (state only)
            • mask (state only)
            • offset (state only)
          • match16bits (state only)
            • value (state only)
            • mask (state only)
            • offset (state only)
          • match32bits (state only)
            • value (state only)
            • mask (state only)
            • offset (state only)
          • ipv4 (state only)
            • match-all (state only)
            • source (state only)
            • destination (state only)
            • protocol (state only)
              • value (state only)
              • mask (state only)
            • tos (state only)
              • value (state only)
              • mask (state only)
            • dscp (state only)
              • value (state only)
          • ipv6 (state only)
            • match-all (state only)
            • source (state only)
            • destination (state only)
            • protocol (state only)
              • value (state only)
              • mask (state only)
            • tos (state only)
              • value (state only)
              • mask (state only)
            • dscp (state only)
              • value (state only)
          • tcp (state only)
            • match-all (state only)
            • source-port (state only)
              • value (state only)
              • mask (state only)
            • destination-port (state only)
              • value (state only)
              • mask (state only)
          • udp (state only)
            • match-all (state only)
            • source-port (state only)
              • value (state only)
              • mask (state only)
            • destination-port (state only)
              • value (state only)
              • mask (state only)
          • icmp (state only)
            • match-all (state only)
            • type (state only)
              • value (state only)
              • mask (state only)
            • code (state only)
              • value (state only)
              • mask (state only)
          • icmpv6 (state only)
            • match-all (state only)
            • type (state only)
              • value (state only)
              • mask (state only)
            • code (state only)
              • value (state only)
              • mask (state only)
        • action (state only)
          • set-mark (state only)
          • restore-connmark (state only)
          • redirect (state only)
          • pass (state only)
          • set-priority (state only)
        • stats (state only)
          • match-packets (state only)
          • drop-packets (state only)
    • egress
      • scheduler (config only)
      • policy (config only)
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • shaper (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
        • shaper (state only)
          • bandwidth (state only)
          • burst (state only)
          • layer1-overhead (state only)
          • queue-size (state only)
          • stats (state only)
            • pass-packets (state only)
            • drop-packets (state only)
      • scheduler (state only)
        • is-root (state only)
        • template-name (state only)
        • core (state only)
        • pq (state only)
          • nb-queue (state only)
          • default-queue (state only)
          • stats (state only)
            • enqueue-packets (state only)
            • enqueue-bytes (state only)
            • xmit-packets (state only)
            • xmit-bytes (state only)
            • drop-queue-full (state only)
            • drop-queue-full-bytes (state only)
          • queue (state only)
            • size (state only)
            • child-scheduler-id (state only)
            • priority (state only)
            • policer (state only)
              • bandwidth (state only)
              • burst (state only)
              • excess-bandwidth (state only)
              • excess-burst (state only)
              • stats (state only)
                • pass-packets (state only)
                • pass-bytes (state only)
                • pass-excess-packets (state only)
                • pass-excess-bytes (state only)
                • drop-packets (state only)
                • drop-bytes (state only)
            • shaper (state only)
              • bandwidth (state only)
              • burst (state only)
              • layer1-overhead (state only)
              • queue-size (state only)
              • stats (state only)
                • pass-packets (state only)
                • drop-packets (state only)
            • class (state only)
              • stats (state only)
                • match-packets (state only)
            • stats (state only)
              • enqueue-packets (state only)
              • enqueue-bytes (state only)
              • xmit-packets (state only)
              • xmit-bytes (state only)
              • drop-queue-full (state only)
              • drop-queue-full-bytes (state only)
        • pb-dwrr (state only)
          • nb-queue (state only)
          • default-queue (state only)
          • stats (state only)
            • enqueue-packets (state only)
            • enqueue-bytes (state only)
            • xmit-packets (state only)
            • xmit-bytes (state only)
            • drop-queue-full (state only)
            • drop-queue-full-bytes (state only)
          • queue (state only)
            • size (state only)
            • child-scheduler-id (state only)
            • quantum (state only)
            • priority (state only)
            • policer (state only)
              • bandwidth (state only)
              • burst (state only)
              • excess-bandwidth (state only)
              • excess-burst (state only)
              • stats (state only)
                • pass-packets (state only)
                • pass-bytes (state only)
                • pass-excess-packets (state only)
                • pass-excess-bytes (state only)
                • drop-packets (state only)
                • drop-bytes (state only)
            • shaper (state only)
              • bandwidth (state only)
              • burst (state only)
              • layer1-overhead (state only)
              • queue-size (state only)
              • stats (state only)
                • pass-packets (state only)
                • drop-packets (state only)
            • class (state only)
              • stats (state only)
                • match-packets (state only)
            • stats (state only)
              • enqueue-packets (state only)
              • enqueue-bytes (state only)
              • xmit-packets (state only)
              • xmit-bytes (state only)
              • drop-queue-full (state only)
              • drop-queue-full-bytes (state only)
        • htb (state only)
          • nb-queue (state only)
          • default-queue (state only)
          • divisor (state only)
          • stats (state only)
            • enqueue-packets (state only)
            • enqueue-bytes (state only)
            • xmit-packets (state only)
            • xmit-bytes (state only)
            • drop-queue-full (state only)
            • drop-queue-full-bytes (state only)
          • queue (state only)
            • size (state only)
            • child-scheduler-id (state only)
            • bandwidth (state only)
            • burst (state only)
            • ceiling (state only)
            • ceiling-burst (state only)
            • layer1-overhead (state only)
            • quantum (state only)
            • priority (state only)
            • child-queue (state only)
            • policer (state only)
              • bandwidth (state only)
              • burst (state only)
              • excess-bandwidth (state only)
              • excess-burst (state only)
              • stats (state only)
                • pass-packets (state only)
                • pass-bytes (state only)
                • pass-excess-packets (state only)
                • pass-excess-bytes (state only)
                • drop-packets (state only)
                • drop-bytes (state only)
            • shaper (state only)
              • bandwidth (state only)
              • burst (state only)
              • layer1-overhead (state only)
              • queue-size (state only)
              • stats (state only)
                • pass-packets (state only)
                • drop-packets (state only)
            • class (state only)
              • stats (state only)
                • match-packets (state only)
            • stats (state only)
              • enqueue-packets (state only)
              • enqueue-bytes (state only)
              • xmit-packets (state only)
              • xmit-bytes (state only)
              • drop-queue-full (state only)
              • drop-queue-full-bytes (state only)
        • sfq (state only)
          • flows (state only)
          • quantum (state only)
          • limit (state only)
          • stats (state only)
            • enqueue-packets (state only)
            • enqueue-bytes (state only)
            • xmit-packets (state only)
            • xmit-bytes (state only)
            • drop-queue-full (state only)
            • drop-queue-full-bytes (state only)
      • policy (state only)
        • priority (state only)
        • selector (state only)
          • match8bits (state only)
            • value (state only)
            • mask (state only)
            • offset (state only)
          • match16bits (state only)
            • value (state only)
            • mask (state only)
            • offset (state only)
          • match32bits (state only)
            • value (state only)
            • mask (state only)
            • offset (state only)
          • ipv4 (state only)
            • match-all (state only)
            • source (state only)
            • destination (state only)
            • protocol (state only)
              • value (state only)
              • mask (state only)
            • tos (state only)
              • value (state only)
              • mask (state only)
            • dscp (state only)
              • value (state only)
          • ipv6 (state only)
            • match-all (state only)
            • source (state only)
            • destination (state only)
            • protocol (state only)
              • value (state only)
              • mask (state only)
            • tos (state only)
              • value (state only)
              • mask (state only)
            • dscp (state only)
              • value (state only)
          • tcp (state only)
            • match-all (state only)
            • source-port (state only)
              • value (state only)
              • mask (state only)
            • destination-port (state only)
              • value (state only)
              • mask (state only)
          • udp (state only)
            • match-all (state only)
            • source-port (state only)
              • value (state only)
              • mask (state only)
            • destination-port (state only)
              • value (state only)
              • mask (state only)
          • icmp (state only)
            • match-all (state only)
            • type (state only)
              • value (state only)
              • mask (state only)
            • code (state only)
              • value (state only)
              • mask (state only)
          • icmpv6 (state only)
            • match-all (state only)
            • type (state only)
              • value (state only)
              • mask (state only)
            • code (state only)
              • value (state only)
              • mask (state only)
        • action (state only)
          • set-mark (state only)
          • restore-connmark (state only)
          • redirect (state only)
          • pass (state only)
          • set-priority (state only)
        • stats (state only)
          • match-packets (state only)
          • drop-packets (state only)
  • counters (state only)
    • in-octets (state only)
    • in-unicast-pkts (state only)
    • in-discards (state only)
    • in-errors (state only)
    • out-octets (state only)
    • out-unicast-pkts (state only)
    • out-discards (state only)
    • out-errors (state only)
• ipip
  • mtu
  • promiscuous
  • enabled (pushed)
  • description
  • local (mandatory)
  • remote (mandatory)
  • ttl
  • tos
  • link-interface
  • link-vrf
  • ifindex (state only)
  • admin-status (state only)
  • oper-status (state only)
  • last-change (state only)
  • ipv4
    • enabled
    • address
      • peer
      • origin (state only)
  • ipv6
    • enabled
    • address
      • peer
      • origin (state only)
      • status (state only)
  • network-stack
    • ipv4
      • send-redirects
      • accept-redirects
      • accept-source-route
      • arp-announce
      • arp-filter
      • arp-ignore
      • arp-proxy
      • log-invalid-addresses
    • ipv6
      • autoconfiguration
      • accept-duplicate-address-detection
      • accept-router-advert
      • accept-redirects
      • accept-segment-routing
      • accept-source-route
      • router-solicitations
      • use-temporary-addresses
  • qos
    • ingress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
    • egress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
  • counters (state only)
    • in-octets (state only)
    • in-unicast-pkts (state only)
    • in-discards (state only)
    • in-errors (state only)
    • out-octets (state only)
    • out-unicast-pkts (state only)
    • out-discards (state only)
    • out-errors (state only)
• lag
  • mtu
  • promiscuous
  • enabled (pushed)
  • description
  • mode (mandatory)
  • xmit-hash-policy
  • lacp-rate
  • mii-link-monitoring
  • arp-interval
  • arp-ip-target
  • ifindex (state only)
  • admin-status (state only)
  • oper-status (state only)
  • last-change (state only)
  • ipv4
    • enabled
    • address
      • peer
      • origin (state only)
    • neighbor
      • link-layer-address (mandatory)
      • state (state only)
    • dhcp
      • enabled
      • timeout
      • retry
      • select-timeout
      • reboot
      • initial-interval
      • dhcp-lease-time
      • dhcp-client-identifier-ascii
      • dhcp-client-identifier-hexa
      • host-name
      • request
      • current-lease (state only)
        • fixed-address (state only)
        • renew (state only)
        • rebind (state only)
        • expire (state only)
  • ethernet
    • mac-address (pushed)
  • ipv6
    • enabled
    • address
      • peer
      • origin (state only)
      • status (state only)
    • neighbor
      • link-layer-address (mandatory)
      • router (state only)
      • state (state only)
  • network-stack
    • ipv4
      • send-redirects
      • accept-redirects
      • accept-source-route
      • arp-announce
      • arp-filter
      • arp-ignore
      • arp-proxy
      • log-invalid-addresses
    • ipv6
      • autoconfiguration
      • accept-duplicate-address-detection
      • accept-router-advert
      • accept-redirects
      • accept-segment-routing
      • accept-source-route
      • router-solicitations
      • use-temporary-addresses
  • link-interface
    • state (state only)
    • link (state only)
    • failure-count (state only)
  • primary
    • interface (mandatory)
    • reselect-policy
  • qos
    • ingress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
    • egress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
  • counters (state only)
    • in-octets (state only)
    • in-unicast-pkts (state only)
    • in-discards (state only)
    • in-errors (state only)
    • out-octets (state only)
    • out-unicast-pkts (state only)
    • out-discards (state only)
    • out-errors (state only)
• loopback
  • mtu
  • promiscuous
  • enabled (pushed)
  • description
  • ifindex (state only)
  • admin-status (state only)
  • oper-status (state only)
  • last-change (state only)
  • ipv4
    • enabled
    • address
      • peer
      • origin (state only)
    • neighbor
      • link-layer-address (mandatory)
      • state (state only)
    • dhcp
      • enabled
      • timeout
      • retry
      • select-timeout
      • reboot
      • initial-interval
      • dhcp-lease-time
      • dhcp-client-identifier-ascii
      • dhcp-client-identifier-hexa
      • host-name
      • request
      • current-lease (state only)
        • fixed-address (state only)
        • renew (state only)
        • rebind (state only)
        • expire (state only)
  • ipv6
    • enabled
    • address
      • peer
      • origin (state only)
      • status (state only)
    • neighbor
      • link-layer-address (mandatory)
      • router (state only)
      • state (state only)
  • network-stack
    • ipv4
      • send-redirects
      • accept-redirects
      • accept-source-route
      • arp-announce
      • arp-filter
      • arp-ignore
      • arp-proxy
      • log-invalid-addresses
    • ipv6
      • autoconfiguration
      • accept-duplicate-address-detection
      • accept-router-advert
      • accept-redirects
      • accept-segment-routing
      • accept-source-route
      • router-solicitations
      • use-temporary-addresses
  • ethernet
    • mac-address (pushed)
  • counters (state only)
    • in-octets (state only)
    • in-unicast-pkts (state only)
    • in-discards (state only)
    • in-errors (state only)
    • out-octets (state only)
    • out-unicast-pkts (state only)
    • out-discards (state only)
    • out-errors (state only)
• physical
  • mtu
  • promiscuous
  • enabled (pushed)
  • description
  • port (mandatory)
  • rx-cp-protection
  • rx-cp-protection-offload
  • tx-cp-protection
  • ifindex (state only)
  • admin-status (state only)
  • oper-status (state only)
  • last-change (state only)
  • ipv4
    • enabled
    • address
      • peer
      • origin (state only)
    • neighbor
      • link-layer-address (mandatory)
      • state (state only)
    • dhcp
      • enabled
      • timeout
      • retry
      • select-timeout
      • reboot
      • initial-interval
      • dhcp-lease-time
      • dhcp-client-identifier-ascii
      • dhcp-client-identifier-hexa
      • host-name
      • request
      • current-lease (state only)
        • fixed-address (state only)
        • renew (state only)
        • rebind (state only)
        • expire (state only)
  • ipv6
    • enabled
    • address
      • peer
      • origin (state only)
      • status (state only)
    • neighbor
      • link-layer-address (mandatory)
      • router (state only)
      • state (state only)
  • network-stack
    • ipv4
      • send-redirects
      • accept-redirects
      • accept-source-route
      • arp-announce
      • arp-filter
      • arp-ignore
      • arp-proxy
      • log-invalid-addresses
    • ipv6
      • autoconfiguration
      • accept-duplicate-address-detection
      • accept-router-advert
      • accept-redirects
      • accept-segment-routing
      • accept-source-route
      • router-solicitations
      • use-temporary-addresses
  • ethernet
    • mac-address (pushed)
    • auto-negotiate
    • duplex-mode
    • port-speed
    • flow-control-rx
    • flow-control-tx
  • qos
    • ingress
      • policy (config only)
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
      • policy (state only)
        • priority (state only)
        • selector (state only)
          • match8bits (state only)
            • value (state only)
            • mask (state only)
            • offset (state only)
          • match16bits (state only)
            • value (state only)
            • mask (state only)
            • offset (state only)
          • match32bits (state only)
            • value (state only)
            • mask (state only)
            • offset (state only)
          • ipv4 (state only)
            • match-all (state only)
            • source (state only)
            • destination (state only)
            • protocol (state only)
              • value (state only)
              • mask (state only)
            • tos (state only)
              • value (state only)
              • mask (state only)
            • dscp (state only)
              • value (state only)
          • ipv6 (state only)
            • match-all (state only)
            • source (state only)
            • destination (state only)
            • protocol (state only)
              • value (state only)
              • mask (state only)
            • tos (state only)
              • value (state only)
              • mask (state only)
            • dscp (state only)
              • value (state only)
          • tcp (state only)
            • match-all (state only)
            • source-port (state only)
              • value (state only)
              • mask (state only)
            • destination-port (state only)
              • value (state only)
              • mask (state only)
          • udp (state only)
            • match-all (state only)
            • source-port (state only)
              • value (state only)
              • mask (state only)
            • destination-port (state only)
              • value (state only)
              • mask (state only)
          • icmp (state only)
            • match-all (state only)
            • type (state only)
              • value (state only)
              • mask (state only)
            • code (state only)
              • value (state only)
              • mask (state only)
          • icmpv6 (state only)
            • match-all (state only)
            • type (state only)
              • value (state only)
              • mask (state only)
            • code (state only)
              • value (state only)
              • mask (state only)
        • action (state only)
          • set-mark (state only)
          • restore-connmark (state only)
          • redirect (state only)
          • pass (state only)
          • set-priority (state only)
        • stats (state only)
          • match-packets (state only)
          • drop-packets (state only)
    • egress
      • scheduler (config only)
      • policy (config only)
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • shaper (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
        • shaper (state only)
          • bandwidth (state only)
          • burst (state only)
          • layer1-overhead (state only)
          • queue-size (state only)
          • stats (state only)
            • pass-packets (state only)
            • drop-packets (state only)
      • scheduler (state only)
        • is-root (state only)
        • template-name (state only)
        • core (state only)
        • pq (state only)
          • nb-queue (state only)
          • default-queue (state only)
          • stats (state only)
            • enqueue-packets (state only)
            • enqueue-bytes (state only)
            • xmit-packets (state only)
            • xmit-bytes (state only)
            • drop-queue-full (state only)
            • drop-queue-full-bytes (state only)
          • queue (state only)
            • size (state only)
            • child-scheduler-id (state only)
            • priority (state only)
            • policer (state only)
              • bandwidth (state only)
              • burst (state only)
              • excess-bandwidth (state only)
              • excess-burst (state only)
              • stats (state only)
                • pass-packets (state only)
                • pass-bytes (state only)
                • pass-excess-packets (state only)
                • pass-excess-bytes (state only)
                • drop-packets (state only)
                • drop-bytes (state only)
            • shaper (state only)
              • bandwidth (state only)
              • burst (state only)
              • layer1-overhead (state only)
              • queue-size (state only)
              • stats (state only)
                • pass-packets (state only)
                • drop-packets (state only)
            • class (state only)
              • stats (state only)
                • match-packets (state only)
            • stats (state only)
              • enqueue-packets (state only)
              • enqueue-bytes (state only)
              • xmit-packets (state only)
              • xmit-bytes (state only)
              • drop-queue-full (state only)
              • drop-queue-full-bytes (state only)
        • pb-dwrr (state only)
          • nb-queue (state only)
          • default-queue (state only)
          • stats (state only)
            • enqueue-packets (state only)
            • enqueue-bytes (state only)
            • xmit-packets (state only)
            • xmit-bytes (state only)
            • drop-queue-full (state only)
            • drop-queue-full-bytes (state only)
          • queue (state only)
            • size (state only)
            • child-scheduler-id (state only)
            • quantum (state only)
            • priority (state only)
            • policer (state only)
              • bandwidth (state only)
              • burst (state only)
              • excess-bandwidth (state only)
              • excess-burst (state only)
              • stats (state only)
                • pass-packets (state only)
                • pass-bytes (state only)
                • pass-excess-packets (state only)
                • pass-excess-bytes (state only)
                • drop-packets (state only)
                • drop-bytes (state only)
            • shaper (state only)
              • bandwidth (state only)
              • burst (state only)
              • layer1-overhead (state only)
              • queue-size (state only)
              • stats (state only)
                • pass-packets (state only)
                • drop-packets (state only)
            • class (state only)
              • stats (state only)
                • match-packets (state only)
            • stats (state only)
              • enqueue-packets (state only)
              • enqueue-bytes (state only)
              • xmit-packets (state only)
              • xmit-bytes (state only)
              • drop-queue-full (state only)
              • drop-queue-full-bytes (state only)
        • htb (state only)
          • nb-queue (state only)
          • default-queue (state only)
          • divisor (state only)
          • stats (state only)
            • enqueue-packets (state only)
            • enqueue-bytes (state only)
            • xmit-packets (state only)
            • xmit-bytes (state only)
            • drop-queue-full (state only)
            • drop-queue-full-bytes (state only)
          • queue (state only)
            • size (state only)
            • child-scheduler-id (state only)
            • bandwidth (state only)
            • burst (state only)
            • ceiling (state only)
            • ceiling-burst (state only)
            • layer1-overhead (state only)
            • quantum (state only)
            • priority (state only)
            • child-queue (state only)
            • policer (state only)
              • bandwidth (state only)
              • burst (state only)
              • excess-bandwidth (state only)
              • excess-burst (state only)
              • stats (state only)
                • pass-packets (state only)
                • pass-bytes (state only)
                • pass-excess-packets (state only)
                • pass-excess-bytes (state only)
                • drop-packets (state only)
                • drop-bytes (state only)
            • shaper (state only)
              • bandwidth (state only)
              • burst (state only)
              • layer1-overhead (state only)
              • queue-size (state only)
              • stats (state only)
                • pass-packets (state only)
                • drop-packets (state only)
            • class (state only)
              • stats (state only)
                • match-packets (state only)
            • stats (state only)
              • enqueue-packets (state only)
              • enqueue-bytes (state only)
              • xmit-packets (state only)
              • xmit-bytes (state only)
              • drop-queue-full (state only)
              • drop-queue-full-bytes (state only)
        • sfq (state only)
          • flows (state only)
          • quantum (state only)
          • limit (state only)
          • stats (state only)
            • enqueue-packets (state only)
            • enqueue-bytes (state only)
            • xmit-packets (state only)
            • xmit-bytes (state only)
            • drop-queue-full (state only)
            • drop-queue-full-bytes (state only)
      • policy (state only)
        • priority (state only)
        • selector (state only)
          • match8bits (state only)
            • value (state only)
            • mask (state only)
            • offset (state only)
          • match16bits (state only)
            • value (state only)
            • mask (state only)
            • offset (state only)
          • match32bits (state only)
            • value (state only)
            • mask (state only)
            • offset (state only)
          • ipv4 (state only)
            • match-all (state only)
            • source (state only)
            • destination (state only)
            • protocol (state only)
              • value (state only)
              • mask (state only)
            • tos (state only)
              • value (state only)
              • mask (state only)
            • dscp (state only)
              • value (state only)
          • ipv6 (state only)
            • match-all (state only)
            • source (state only)
            • destination (state only)
            • protocol (state only)
              • value (state only)
              • mask (state only)
            • tos (state only)
              • value (state only)
              • mask (state only)
            • dscp (state only)
              • value (state only)
          • tcp (state only)
            • match-all (state only)
            • source-port (state only)
              • value (state only)
              • mask (state only)
            • destination-port (state only)
              • value (state only)
              • mask (state only)
          • udp (state only)
            • match-all (state only)
            • source-port (state only)
              • value (state only)
              • mask (state only)
            • destination-port (state only)
              • value (state only)
              • mask (state only)
          • icmp (state only)
            • match-all (state only)
            • type (state only)
              • value (state only)
              • mask (state only)
            • code (state only)
              • value (state only)
              • mask (state only)
          • icmpv6 (state only)
            • match-all (state only)
            • type (state only)
              • value (state only)
              • mask (state only)
            • code (state only)
              • value (state only)
              • mask (state only)
        • action (state only)
          • set-mark (state only)
          • restore-connmark (state only)
          • redirect (state only)
          • pass (state only)
          • set-priority (state only)
        • stats (state only)
          • match-packets (state only)
          • drop-packets (state only)
  • counters (state only)
    • in-octets (state only)
    • in-unicast-pkts (state only)
    • in-discards (state only)
    • in-errors (state only)
    • out-octets (state only)
    • out-unicast-pkts (state only)
    • out-discards (state only)
    • out-errors (state only)
• pimreg (state only)
  • mtu (state only)
  • promiscuous (state only)
  • enabled (state only) (pushed)
  • description (state only)
  • ifindex (state only)
  • admin-status (state only)
  • oper-status (state only)
  • last-change (state only)
  • ipv4 (state only)
    • enabled (state only)
    • address (state only)
      • peer (state only)
      • origin (state only)
    • neighbor (state only)
      • link-layer-address (state only)
      • state (state only)
    • dhcp (state only)
      • enabled (state only)
      • timeout (state only)
      • retry (state only)
      • select-timeout (state only)
      • reboot (state only)
      • initial-interval (state only)
      • dhcp-lease-time (state only)
      • dhcp-client-identifier-ascii (state only)
      • dhcp-client-identifier-hexa (state only)
      • host-name (state only)
      • request (state only)
      • current-lease (state only)
        • fixed-address (state only)
        • renew (state only)
        • rebind (state only)
        • expire (state only)
  • ipv6 (state only)
    • enabled (state only)
    • address (state only)
      • peer (state only)
      • origin (state only)
      • status (state only)
    • neighbor (state only)
      • link-layer-address (state only)
      • router (state only)
      • state (state only)
  • counters (state only)
    • in-octets (state only)
    • in-unicast-pkts (state only)
    • in-discards (state only)
    • in-errors (state only)
    • out-octets (state only)
    • out-unicast-pkts (state only)
    • out-discards (state only)
    • out-errors (state only)
  • network-stack (state only)
    • ipv4 (state only)
      • send-redirects (state only)
      • accept-redirects (state only)
      • accept-source-route (state only)
      • arp-announce (state only)
      • arp-filter (state only)
      • arp-ignore (state only)
      • arp-proxy (state only)
      • log-invalid-addresses (state only)
    • ipv6 (state only)
      • autoconfiguration (state only)
      • accept-duplicate-address-detection (state only)
      • accept-router-advert (state only)
      • accept-redirects (state only)
      • accept-segment-routing (state only)
      • accept-source-route (state only)
      • router-solicitations (state only)
      • use-temporary-addresses (state only)
• pppoe
  • enabled
  • link-interface (mandatory)
  • service-name
  • ac-name
  • remote-mac-address
  • mtu
  • mru
  • request
  • link-status (state only)
  • session (state only)
  • rpf (state only)
  • qos
    • ingress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
    • egress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
  • auth
    • reply
    • user (mandatory)
    • secret (mandatory) (hidden)
  • ipcp
    • enabled
    • local-address
    • remote-address
  • ipv6cp
    • enabled
    • local-ifid
    • remote-ifid
  • lcp
    • echo-interval
    • echo-failure
  • logging
    • enabled
• svti
  • mtu
  • promiscuous
  • enabled (pushed)
  • description
  • svti-id (mandatory)
  • link-vrf
  • ifindex (state only)
  • admin-status (state only)
  • oper-status (state only)
  • last-change (state only)
  • link-interface (state only)
  • ipv4
    • enabled
    • address
      • peer
      • origin (state only)
    • neighbor
      • link-layer-address (mandatory)
      • state (state only)
    • dhcp
      • enabled
      • timeout
      • retry
      • select-timeout
      • reboot
      • initial-interval
      • dhcp-lease-time
      • dhcp-client-identifier-ascii
      • dhcp-client-identifier-hexa
      • host-name
      • request
      • current-lease (state only)
        • fixed-address (state only)
        • renew (state only)
        • rebind (state only)
        • expire (state only)
  • ethernet
    • mac-address (pushed)
  • ipv6
    • enabled
    • address
      • peer
      • origin (state only)
      • status (state only)
    • neighbor
      • link-layer-address (mandatory)
      • router (state only)
      • state (state only)
  • network-stack
    • ipv4
      • send-redirects
      • accept-redirects
      • accept-source-route
      • arp-announce
      • arp-filter
      • arp-ignore
      • arp-proxy
      • log-invalid-addresses
    • ipv6
      • autoconfiguration
      • accept-duplicate-address-detection
      • accept-router-advert
      • accept-redirects
      • accept-segment-routing
      • accept-source-route
      • router-solicitations
      • use-temporary-addresses
  • qos
    • ingress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
    • egress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
  • counters (state only)
    • in-octets (state only)
    • in-unicast-pkts (state only)
    • in-discards (state only)
    • in-errors (state only)
    • out-octets (state only)
    • out-unicast-pkts (state only)
    • out-discards (state only)
    • out-errors (state only)
• svti-template (config only)
  • mtu (config only)
  • install-routes-to (config only)
• system-loopback (state only)
  • mtu (state only)
  • promiscuous (state only)
  • enabled (state only) (pushed)
  • description (state only)
  • ifindex (state only)
  • admin-status (state only)
  • oper-status (state only)
  • last-change (state only)
  • ipv4 (state only)
    • enabled (state only)
    • address (state only)
      • peer (state only)
      • origin (state only)
    • neighbor (state only)
      • link-layer-address (state only)
      • state (state only)
    • dhcp (state only)
      • enabled (state only)
      • timeout (state only)
      • retry (state only)
      • select-timeout (state only)
      • reboot (state only)
      • initial-interval (state only)
      • dhcp-lease-time (state only)
      • dhcp-client-identifier-ascii (state only)
      • dhcp-client-identifier-hexa (state only)
      • host-name (state only)
      • request (state only)
      • current-lease (state only)
        • fixed-address (state only)
        • renew (state only)
        • rebind (state only)
        • expire (state only)
  • ipv6 (state only)
    • enabled (state only)
    • address (state only)
      • peer (state only)
      • origin (state only)
      • status (state only)
    • neighbor (state only)
      • link-layer-address (state only)
      • router (state only)
      • state (state only)
  • counters (state only)
    • in-octets (state only)
    • in-unicast-pkts (state only)
    • in-discards (state only)
    • in-errors (state only)
    • out-octets (state only)
    • out-unicast-pkts (state only)
    • out-discards (state only)
    • out-errors (state only)
• veth
  • mtu
  • promiscuous
  • enabled (pushed)
  • description
  • link-interface (mandatory)
  • link-vrf (mandatory)
  • ifindex (state only)
  • admin-status (state only)
  • oper-status (state only)
  • last-change (state only)
  • ipv4
    • enabled
    • address
      • peer
      • origin (state only)
    • neighbor
      • link-layer-address (mandatory)
      • state (state only)
    • dhcp
      • enabled
      • timeout
      • retry
      • select-timeout
      • reboot
      • initial-interval
      • dhcp-lease-time
      • dhcp-client-identifier-ascii
      • dhcp-client-identifier-hexa
      • host-name
      • request
      • current-lease (state only)
        • fixed-address (state only)
        • renew (state only)
        • rebind (state only)
        • expire (state only)
  • ipv6
    • enabled
    • address
      • peer
      • origin (state only)
      • status (state only)
    • neighbor
      • link-layer-address (mandatory)
      • router (state only)
      • state (state only)
  • network-stack
    • ipv4
      • send-redirects
      • accept-redirects
      • accept-source-route
      • arp-announce
      • arp-filter
      • arp-ignore
      • arp-proxy
      • log-invalid-addresses
    • ipv6
      • autoconfiguration
      • accept-duplicate-address-detection
      • accept-router-advert
      • accept-redirects
      • accept-segment-routing
      • accept-source-route
      • router-solicitations
      • use-temporary-addresses
  • ethernet
    • mac-address (pushed)
  • qos
    • ingress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
    • egress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
  • counters (state only)
    • in-octets (state only)
    • in-unicast-pkts (state only)
    • in-discards (state only)
    • in-errors (state only)
    • out-octets (state only)
    • out-unicast-pkts (state only)
    • out-discards (state only)
    • out-errors (state only)
• vlan
  • mtu
  • promiscuous
  • enabled (pushed)
  • description
  • vlan-id (mandatory)
  • link-interface (mandatory)
  • protocol
  • link-vrf
  • ifindex (state only)
  • admin-status (state only)
  • oper-status (state only)
  • last-change (state only)
  • ipv4
    • enabled
    • address
      • peer
      • origin (state only)
    • neighbor
      • link-layer-address (mandatory)
      • state (state only)
    • dhcp
      • enabled
      • timeout
      • retry
      • select-timeout
      • reboot
      • initial-interval
      • dhcp-lease-time
      • dhcp-client-identifier-ascii
      • dhcp-client-identifier-hexa
      • host-name
      • request
      • current-lease (state only)
        • fixed-address (state only)
        • renew (state only)
        • rebind (state only)
        • expire (state only)
  • ethernet
    • mac-address (pushed)
  • ipv6
    • enabled
    • address
      • peer
      • origin (state only)
      • status (state only)
    • neighbor
      • link-layer-address (mandatory)
      • router (state only)
      • state (state only)
  • network-stack
    • ipv4
      • send-redirects
      • accept-redirects
      • accept-source-route
      • arp-announce
      • arp-filter
      • arp-ignore
      • arp-proxy
      • log-invalid-addresses
    • ipv6
      • autoconfiguration
      • accept-duplicate-address-detection
      • accept-router-advert
      • accept-redirects
      • accept-segment-routing
      • accept-source-route
      • router-solicitations
      • use-temporary-addresses
  • egress-priority-mapping
    • to
  • ingress-priority-mapping
    • to
  • qos
    • ingress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
    • egress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
  • counters (state only)
    • in-octets (state only)
    • in-unicast-pkts (state only)
    • in-discards (state only)
    • in-errors (state only)
    • out-octets (state only)
    • out-unicast-pkts (state only)
    • out-discards (state only)
    • out-errors (state only)
• vxlan
  • mtu
  • promiscuous
  • enabled (pushed)
  • description
  • vni (mandatory)
  • group
  • remote
  • local
  • ttl
  • tos
  • link-interface
  • link-vrf
  • learning
  • gbp
  • dst
  • ifindex (state only)
  • admin-status (state only)
  • oper-status (state only)
  • last-change (state only)
  • ipv4
    • enabled
    • address
      • peer
      • origin (state only)
    • neighbor
      • link-layer-address (mandatory)
      • state (state only)
    • dhcp
      • enabled
      • timeout
      • retry
      • select-timeout
      • reboot
      • initial-interval
      • dhcp-lease-time
      • dhcp-client-identifier-ascii
      • dhcp-client-identifier-hexa
      • host-name
      • request
      • current-lease (state only)
        • fixed-address (state only)
        • renew (state only)
        • rebind (state only)
        • expire (state only)
    • fdb
      • link-interface
      • port
      • vni
      • state (state only)
  • ethernet
    • mac-address (pushed)
  • ipv6
    • enabled
    • address
      • peer
      • origin (state only)
      • status (state only)
    • neighbor
      • link-layer-address (mandatory)
      • router (state only)
      • state (state only)
    • fdb
      • link-interface
      • port
      • vni
      • state (state only)
  • network-stack
    • ipv4
      • send-redirects
      • accept-redirects
      • accept-source-route
      • arp-announce
      • arp-filter
      • arp-ignore
      • arp-proxy
      • log-invalid-addresses
    • ipv6
      • autoconfiguration
      • accept-duplicate-address-detection
      • accept-router-advert
      • accept-redirects
      • accept-segment-routing
      • accept-source-route
      • router-solicitations
      • use-temporary-addresses
  • src-range
    • <uint16>
    • <uint16>
  • qos
    • ingress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
    • egress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
  • counters (state only)
    • in-octets (state only)
    • in-unicast-pkts (state only)
    • in-discards (state only)
    • in-errors (state only)
    • out-octets (state only)
    • out-unicast-pkts (state only)
    • out-discards (state only)
    • out-errors (state only)
• xvrf
  • mtu
  • promiscuous
  • enabled (pushed)
  • description
  • link-interface (mandatory)
  • link-vrf (mandatory)
  • ifindex (state only)
  • admin-status (state only)
  • oper-status (state only)
  • last-change (state only)
  • qos
    • ingress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
    • egress
      • rate-limit
        • policer (config only)
        • shared-policer (config only)
        • policer (state only)
          • bandwidth (state only)
          • burst (state only)
          • excess-bandwidth (state only)
          • excess-burst (state only)
          • shared-policer (state only)
          • stats (state only)
            • pass-packets (state only)
            • pass-bytes (state only)
            • pass-excess-packets (state only)
            • pass-excess-bytes (state only)
            • drop-packets (state only)
            • drop-bytes (state only)
  • counters (state only)
    • in-octets (state only)
    • in-unicast-pkts (state only)
    • in-discards (state only)
    • in-errors (state only)
    • out-octets (state only)
    • out-unicast-pkts (state only)
    • out-discards (state only)
    • out-errors (state only)